background image

507651-01

Page 28  of  32

Issue 1907

Other Unit Adjustments

Primary Limit

The primary limit is located on the heating compartment 

vestibule  panel.  The  secondary  limits  (if  equipped)  are 

located in the blower compartment, attached to the back 

side of the blower. These auto reset limits are factory-set 

and require no adjustment.

Thermal Switch

These manually reset switches are located on the front of 

the box.

Pressure Switch

The pressure switch is located in the heating compartment 

adjacent to the combustion air inducer. The switch checks 

for proper combustion air inducer operation before allowing 

ignition  trial.  The  switch  is  factory-set  and  requires  no 

adjustment.

Temperature Rise

After the furnace has been started, and supply and return 

air temperatures have been allowed to stabilize, check the 

temperature rise. If necessary, adjust the blower speed to 

maintain the temperature rise within the range shown on 

the unit nameplate. Increase the blower speed to decrease 

the temperature. Decrease the blower speed to increase 

the temperature rise. Failure to adjust the temperature rise 

may cause erratic limit operation.

Fan Control

The heat fan-on time of 30 seconds is not adjustable. The 

heat fan-off delay (amount of time that the blower operates 

after the heat demand has been satisfied) may be adjusted 

by changing the jumper position across the five pins on the 

integrated control. The unit is shipped with a factory fan-

off delay setting of 90 seconds. The fan-off delay affects 

comfort and is adjustable to satisfy individual applications. 

Adjust the fan-off delay to achieve a supply air temperature 

between  90°  and  110°F  at  the  moment  that  the  blower 

is  de-energized.  Longer  off  delay  settings  provide  lower 

return  air  temperatures;  shorter  settings  provide  higher 

return air temperatures. See Figure 26.

Constant Torque Motor

These  units  are  equipped  with  a  constant  torque  ECM 

motor. It has a DC motor coupled to an electronic control 

module  both  contained  in  the  same  motor  housing.  The 

motor is programmed to provide constant torque at each of 

the five selectable speeds. The motor has five speed taps. 

Each tap requires 24 volts to energize.

HEAT FAN

OFF TIME IN SECONDS

To adjust fan-off timing, reposition jumper across pins to

achieve desired setting.

NO JUMPER

60 90

12

0

18

0

60 90

12

0

180

60 90

12

0

180

60 90

120 18

0

60 Second 

off Time

90 Second 

off Time

120 Second 

off Time

180 Second 

off Time

Figure 26. Heat Fan Off Time in Seconds

Input Voltage Requirements

The circuit is designed to be operated with AC voltage. A 

voltage of 12 to 33VAC is required to energize the motor. 

Expected current draw will be less than 20mA.

Blower Speeds

Follow the steps below to change the blower speeds.
1.  Turn off electrical power to furnace.
2.  Remove blower access panel.
3.  Disconnect  existing  speed  tap  at  integrated  control 

speed terminal.

NOTE: 

Termination of any unused motor leads must 

be insulated.

4.  Place unused blower speed tap on integrated control 

“PARK” terminal or insulate.

5.  Refer  to  blower  speed  selection  chart  on  unit  wiring 

diagram  for  desired  heating  or  cooling  speed.  See 

Product Specifications for blower performance data.

6.  Connect  selected  speed  tap  at  integrated  control 

speed terminal.

7.  Resecure blower access panel.
8.  Turn on electrical power to furnace.
9.  Recheck temperature rise.

Electronic Ignition

The integrated control has an added feature of an internal 

Watchguard control. The feature serves as an automatic 

reset  device  for  integrated  control  lockout  caused  by 

ignition failure. This type of lockout is usually due to low 

gas line pressure. After one hour of continuous thermostat 

demand  for heat, the Watchguard  will  reset and remake 

thermostat demand to the furnace and automatically reset 

the integrated control to begin the ignition sequence.

Содержание 80G1UHEX Series

































Отзывы: