
1. When the new Body/Anvil is available,
bring the Striker (2), the Whip Hose (14)
and tail assembly components to the
work area for reassembly.
2. Install all of the assemblies in the
Body/Anvil following the assembly pro-
cedures in this section, starting with
section 9.xx.
9.4 Assemble End Cap Components
1. Obtain a push bar to press the Shock Ab-
sorber (11) into the End Cap (10). A
push bar approximately xx-inches long
and 7-3/4-inches in diameter is recom-
mended as shown in Figure 9-1.
2. Lubricate the push bar lightly. It must
press into the End Cap (10) but must not
slide inside the Shock Absorber.
3. Lubricate the O.D. of the Shock Ab-
sorber (11) and the I.D. of End Cap (10)
as shown in Figure 9-1.
4. Position the End Cap (10) in an arbor
press with the threaded end up as shown
in Figure 9-1.
5. Center the Shock Absorber (11) over the
threaded end of the End Cap (10). Fit the
the Shock Absorber into the End Cap
only as far as it will slide freely. Refer to
Figure 9-2-A.
6. Center the press plunger or push bar
over the Shock Absorber as shown in
Figure 9-2-A.
~
CAUTION
DO NOT press Shock Absorber past
the seat at the non-threaded end of
the End Cap.
7. Press the Shock Absorber (11) into the
End Cap (10) until it seats between the
shoulders at opposite ends of the end of
the cap as shown in Figure 9-2-B.
•
If press plunger or standard push bar
is used, stop pressing when the Shock
Absorber snaps under the shoulder at
the threaded (upper) end of the End
Cap.
A
LLIED
Model 5500 Hole-Hog
30
08/25/00
B
A
End Cap
Shock
Absorber
Shock Absorber
Installation
Pusher Bar
Figure 9-2. Press the Shock Absorber into the
End Cap
End Cap
Shock Absorber
Lubricate exterior of
Shock Absorber
Lubricate interior of
End Cap
Recommended
Shock Absorber
Installation Pusher Bar
-inch
Length
Diameter = 7-3/4
= 1-inch
Figure 9-1. End Cap and Shock Absorber in
Press
Содержание 5500
