Allied 045-12 Скачать руководство пользователя

Страница: 9 / 54

507582-04

Page 9 of 54

Issue 2220

Figure 9.

Equipment in Confined Space

(Inlet Air from Ventilated Crawlspace & Outlet Air to

Outside)

NOTE

-The inlet and outlet air openings shall each have a free area

of at least one square inch per 4,000 Btu (645mm

per 1.17kW) per

hour of the total input rating of all equipment in the enclosure.

Roof Terminated

Exhaust Pipe

Furnace

Ventilation

Louvers

(Crawl space)

*Intake Debris Screen Provided)

Inlet Air

(Minimum

12 in.(305mm)

Above crawl

space floor)

Coupling or

3 in. to 2 in.

Transition

(Field Provided)

* See Maximum Vent Lengths table

When communicating with the outdoors through horizontal

ducts, each opening shall have a minimum free area of 1

square inch (645 mm²) per 2,000 Btu (.56 kW) per hour of

the total input rating of all equipment in the enclosure. See

Figure 10.

Figure 10.

Equipment in Confined Space - all Air from

Outside

When ducts are used, they shall be of the same cross-

sectional area as the free area of the openings to which

they connect. The minimum dimension of rectangular

air ducts shall be no less than 3 inches (75 mm). In

calculating free area, the blocking effect of louvers, grilles,

or screens must be considered. If the design and free area

of protective covering is not known for calculating the size

opening required, it may be assumed that wood louvers

will have 20 to 25 percent free area and metal louvers and

grilles will have 60 to 75 percent free area. Louvers and

grilles must be fixed in the open position or interlocked

with the equipment so that they are opened automatically

during equipment operation.

If this unit is being installed in an application with

combustion air coming in from a space serviced by an

exhaust fan, power exhaust fan, or other device which

may create a negative pressure in the space, take care

when sizing the inlet air opening. The inlet air opening

must be sized to accommodate the maximum volume

of exhaust air as well as the maximum volume of

combustion air required for all gas appliances serviced

by this space.

WARNING

Installation

Setting Equipment

Do not install the furnace on its front, back or in the

horizontal position. See Figure 13. Do no connect the

return air ducts to the back of the furnace. Doing so

will adversely affect the operation of the safety control

devices, which could result in personal injury or death.

WARNING

Select a location that allows for the required clearances

that are listed on the unit nameplate. Also consider gas

supply connections, electrical supply, vent connection,

condensate trap and drain connections, and installation

and service clearances [24 inches (610 mm) at unit front].

The unit must be level from side to side. Tilt the unit slightly

(maximum 1/2 in. from level) from back to front to aid in the

draining of the heat exchanger. See Figure 12.

Shipping Bolt Removal

NOTE:

Units with a 1/2 hp blower motors are equipped

with three flexible legs and one rigid leg. The rigid leg

is equipped with a shipping bolt and a flat white plastic

washer (rather than the rubber mounting grommet used

with a flexible mounting leg). See Figure 11. The bolt and

washer must be removed before the furnace is placed into

operation. After the bolt and washer have been removed,

the rigid leg will not touch the blower housing.

Allow for clearances to combustible materials as indicated

on the unit nameplate. Minimum clearances for closet or

alcove installations are shown in Figure 15.

Содержание 045-12























































Результаты поиска

Содержание 045-12

Отзывы:

Похожие инструкции для 045-12

Бренды по названию

Популярные бренды

Allied 045-12, Руководство по установке

Результаты поиска

Содержание 045-12

Отзывы:

Похожие инструкции для 045-12

Бренды по названию

Популярные бренды