Allied Vision Technologies GX1660C Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 41

Allied Vision Technologies GX1660C Скачать руководство пользователя страница 12

GX1660 User Manual

70-0057A-A

Allied Vision Technologies (Canada) Inc.

10

LENS CONTROL PORT

PIN FUNCTION

1

IRIS +

2

IRIS -

3

FOCUS +

4

FOCUS -

5

ZOOM +

6

ZOOM -

7

AUTO IRIS SIGNAL

8

GROUND

LENS CONTROL PORT AS SEEN FROM BACK OF

CAMERA

This  connector  provides  the  signals  necessary  to  control  the  iris,  focus,  and  zoom  of  most
commercially available TV Zoom lenses.  The camera can be configured to operate lenses with
unipolar  voltage  requirements  of  6V  up  to  12V  or  lenses  which  operate  with  bipolar  voltages
from  ±6V  up  to  ±12V.    This  voltage  level  can  be  controlled  through  software.    The  default
voltage will be set to 6V. The current capacity for each axis is 50mA.

CARE MUST BE TAKEN NOT TO EXCEED THE LENS MANUFACTURERS
VOLTAGE SPECIFICATION.

This connector also provides the signals necessary to operate a video auto iris type of lens.

The lens control connector is a Hirose 3260-8S3. The mating cable connector is Hirose 3240-
8P-C(50). This connector can be purchased from AVT Canada Inc. or from

http://www.digikey.com

.

See Addendum for more detail.

«
...
10
11
12
13
14
...
»

Содержание GX1660C










































Отзывы:

Нет отзывов