Allied Telesis Rapier 48w Скачать руководство пользователя страница 18

Страница: 18 / 24

Rapier 48w Switch

Documentation Set

The complete document set for Rapier Series switches includes the following:

■

This Installation and Safety Guide for the Rapier 48w switch

■

The

Rapier 48w Switch Removable Fan Installation Guide

, which describes how

to install AT-FAN04 fan-only modules (FOMs) in the Rapier 48w switch

■

The

Rapier i Series Switch Safety and Statutory Information

booklet, which

contains safety information for all Rapier switches except the Rapier 48w

■

The

Rapier Series Switch Quick Install Guide

, which describes how to install all

Rapier switches except the Rapier 48w

■

The

Rapier Series Switch Hardware Reference

, which contains detailed

information on the hardware features of all Rapier Series switches

■

The

Rapier Series Switch AlliedWare™Operating System Software Reference

, which

contains detailed information on configuring the switch and its software

■

The

Network Service Module Installation and Safety Guide

, which describes how

to install a Network Service Module

■

The

Network Service Module Hardware Reference

, which contains detailed

information on the hardware features of Network Service Modules

■

The

Port Interface Card Installation and Safety Guide

, which describes how to

install a Port Interface Card

■

The

Port Interface Card Hardware Reference

, which contains detailed

information on the hardware features of Port Interface Cards

■

The

Uplink Module Installation and Safety Guide

, which describes how to install

an uplink module

■

The

Uplink Module Hardware Reference

, which contains detailed information

on the hardware features of uplink modules

You can download these documents and updates from

www.alliedtelesis.com/support/software

You need Adobe® Acrobat® Reader® to view, search, or print these
documents. You can download it from

www.adobe.com

The Documentation Tools CD-ROM included with each Rapier 48w switch
contains these documents, plus:

■

AT-TFTP Server for Windows, for transferring files to and from the switch

■

Supported MIBs

■

How-To Notes, Microsoft® Visio® stencils and other resources

Содержание Rapier 48w

























Результаты поиска

Содержание Rapier 48w

Отзывы:

Похожие инструкции для Rapier 48w

Бренды по названию

Популярные бренды

Allied Telesis Rapier 48w, Инструкция по установке и безопасности

Результаты поиска

Содержание Rapier 48w

Отзывы:

Похожие инструкции для Rapier 48w

Бренды по названию

Популярные бренды