Chapter 2 - InterfaceGroup Parameters
MIB Reference Manual - Provisioning MIB
VP500 Communication Unit
9
interfaceVlan-
Group Parameters
The following parameters allow you to define the VLAN settings of the
VP500 communication unit.
interfaceQoSMediaIeee8021QUserPriority
R/W
IEEE 802.1Q VLAN user priority value for VoIP media packet.
This value is used to set the user priority in the TCI field of the
VLAN tag. Tagging user priority is applied only when the filter is
enabled. In the case where the filter for signaling protocol is
disabled and the VLAN option is enabled, the default user priority
declared under the VLAN group will be used. Otherwise, the user
priority set for signaling has precedence over the VLAN default
user priority.
•
7 = High priority
•
0 = Low priority
Default Value
: 6
Yes
Table 7:
Interface QoS Parameters (Continued)
Name
Access
Description
Dynamic
Table 8:
Interface VLAN Parameters
Name
Access
Description
Dynamic
interfaceVlanIeee8021QTaggingEnable
R/W
Enabling IEEE 802.1Q VLAN tagging. With this option enabled,
all packets are tagged with the Virtual ID (VID) specified below.
The default user priority is to be applied in case of general
protocol or when signaling or media protocol filtering is
disabled.WARNING: Enable this option only on compatible LAN
with equipment supporting the VLAN tagging. Otherwise, the Unit
may be unreachable. In this case, please use the reset button to
access and disable VLAN tagging - in the reset mode, tagging is
not permitted. See IEEE 802.1Q for more information on this
topic.
0 =
Disable
1 =
Enable
Default Value
: 0
Yes
interfaceVlanIeee8021QVirtualLanID
R/W
IEEE 802.1Q Virtual LAN ID. This is theVID to be applied in the
TCI field when tagging is enabled. The value 1 is the default Port
VID (PVID) for bridge port. The 4095 VID (0xFFF) is reserved for
implementation use and it shall not be used in tag header.NOTE:
As per standard, some bridges may not support the full range of
VID.
Default Value
: 1
Yes
interfaceVlanIeee8021QDefaultUserPriority
R/W
IEEE 802.1Q Virtual LAN default user priority. This is the user
priority to be applied in the TCI field when tagging is enabled.
This value applies to all protocols for which no priority filtering is
enabled (e.g. ARP, ICMP).
•
7 = High priority
•
0 = Low priority
Default Value
: 6
Yes
Содержание MIB Structure (SIP/MGCP/NCS)
