manualshive.com logo in svg

Allied Telesis CentreCOM AT-3004SL, Руководство пользователя

Поделиться
Скачать
Allied Telesis CentreCOM AT-3004SL Скачать руководство пользователя страница 28

 

Glossary

20

 

MANAGEMENT AGENT

 

—Software that is used to view hub activity and 

set hub variables.

 

MAU

 

—See Medium Attachment Unit

 

MAU to MAU, HUB to HUB WIRING

 

—10BASE-T MAU to MAU or hub 

to hub wiring generally requires a cross-over cable located somewhere along 
the UTP cable run. This may commonly occur at the punch-down block or 
between the RJ45 wall receptacle and the workstation. 

 

MAU/TRANSCEIVER

 

—An Ethernet transceiver is a MAU. A 10BASE-T 

MAU interfaces the UTP media to an AUI port on a workstation, repeater, 
bridge, or other Ethernet devices.

 

MDI

 

—See Medium Dependent Interface

 

MEDIUM ATTACHMENT UNIT (MAU)

 

—In a LAN, a device used in a 

data station to couple the DTE to the transmission medium.

 

MEDIUM DEPENDENT INTERFACE (MDI)

 

—The mechanical and 

electrical interface between the trunk cable medium and the MAU.

 

N-SERIES

 

—A barrel shaped, threaded connector used on 10BASE5 (thick 

Ethernet) coaxial cable.

 

PATCH PANEL

 

—A 10BASE-T patch panel may be between a punch-down 

block and UTP workstation. The patch panel generally has a female RJ45 
connector on the front for each workstation and a Telco (RJ21) connector on 
the back, which are wired to a punch-down block. This provides a convenient 
way for the installer or network manager to connect the hub 10BASE-T ports 
into the desired building locations.

 

PHYSICAL MEDIUM ATTACHMENT (PMA)

 

—The portion of the MAU 

that contains the functional circuitry.

 

PHYSICAL SIGNALING (PLS)

 

—That portion of the physical layer 

contained within the DTE that provides the logical and functional coupling 
between MAU and data link layers.

 

POLARITY CORRECTION

 

—Many 10BASE-T UTP ports have a Polarity 

Correction function. If the UTP wiring has RD- and RD+ inadvertently 
crossed, the polarity correction function will sample the signal and electrically 
swap the wires. If the TD- and TD+ wires are crossed, the correction would 
occur at the MAU on the other end of the UTP link. This occurs within a 
single pair and should not be confused with the cross-over cable.

 

PROPAGATION DELAY

 

—The time it takes a signal to travel from the 

input of a system component to the output. Usually measured in nanoseconds. 
IEEE 802.3 has specific propagation delay maximums for computing 
propagation budgets when designing a LAN. Cable length plays a major role 
in propagation delay. [i.e, a 50 meters (164 ft.) AUI cable has a maximum 
allowable propagation delay of 257 ns.] The propagation delay of cable is 
dependent on length and velocity factor of the cable type. There are also 
propagation delays associated with electronics attached to the system.

Содержание CentreCOM AT-3004SL
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды