Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 54 / 214

Chapter 1: Overview

Note

Breakout cables are supported in 26-port x930 Switches. They are

not supported in 52-port switches.

Each transceiver port has one LED. The states of the LED are defined in

Table 12.

The LED states for breakout cables are described in Table 13.

Table 12. AT-StackQS Card LEDs

LED

State

Description

L/A (Link/

Activity)

Off

The port is not connected to another

network device, the device is not powered

on, or the LEDs are turned off. To turn on

the LEDs, use the eco-friendly button.

Solid green

The port has established a 40Gbps link to

network device.

Flashing

green

The port is transmitting or receiving

network packets.

Table 13. AT-StackQS Card LEDs with 10Gbps Breakout Cables

State

Description

Solid Amber

At least one of the four ports on the

breakout cable has established a 10Gbps

link to a network device.

Flashing Amber

At least one of the four ports on the

breakout cable is sending or receiving

data.

Off

Possible causes of this state are listed

here:
- The transceiver port is empty.
- None of the ports on the breakout cable

have established links to network

devices.

- The LEDs are turned off. To turn on the

LEDs, use the eco-friendly button.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды