Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 48

Страница: 48 / 214

Chapter 1: Overview

The LEDs are described in Table 10.

LEDs for the

Stacking Ports

SFP+ ports 27/S1 and 28/S2 on the 28-port switches and ports 51/S1 and

52/S2 on the 52-port switches may be used as stacking ports to build a

VCStack of up to eight switches at 10Gbps speeds or four switches at

1000M speeds. For background information, refer to Chapter 2, “Virtual

Chassis Stacking” on page 57 . Table 11 on page 49 defines the LED

states when the ports are used to build a stack of switches.

Table 10. SFP+ Port LEDs

LED

State

Description

Link/Activity

Solid green

The SFP+ transceiver in the port has

established a link at 10 Gbps to a network

device.

Flashing

green

The SFP+ transceiver is receiving or

transmitting packets to a network device

at 10 Gbps.

Solid amber The SFP transceiver in the port has

established a link at 1000 Mbps to a

network device.

Flashing

amber

The SFP transceiver is receiving or

transmitting packets to a network device

at 1000 Mbps.

Off

The port is empty, the SFP or SFP+

transceiver has not established a link to a

network device, or the LEDs are turned

off. To turn on the LEDs, use the eco-

friendly button.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды