Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 34 / 214

Chapter 1: Overview

Power Budget

The power budget defines the maximum amount of power the switch can

supply to the powered devices on its ports. The higher the budget, the

more PoE devices the switch can support at one time.

The power budgets for the AT-x930-28GPX and AT-x930-52GPX

Switches depend on several factors. The first is the power supply model.

The power budgets of the five power supplies are listed in Table 3.

Note

The AT-PWR150, AT-PWR250 and AT-PWR250-80 Power

Supplies are intended for the non-PoE AT-x930-28GTX, AT-x930-

28GSTX, and AT-x930-52GTX Switches. They are not intended for

the AT-x930-28GPX and AT-x930-52GPX Switches because they

do not provide power for PoE + devices. You may install them in the

PoE+ switches, but the switches will not support PoE devices.

Another factor that determines the power budget of the switch is the

number of PoE power supplies in the device. The power budget of a PoE

switch that has only one PoE power supply is equal to the budget of the

power supply. For example, a switch that has one AT-PWR1200 Power

Supply has a power budget of 740W for powered devices.

Table 2. IEEE Powered Device Classes

Class

Maximum Power

Output from a Switch

Port

PD Power Range

15.4W

0.44W to 12.95W

4.0W

0.44W to 3.84W

7.0W

3.84W to 6.49W

15.4W

6.49W to 12.95W

30.0W

12.95W to 25.5W

Table 3. Power Supply Budgets of the Power Supplies

Power Supply

Power Budget for PoE Devices

AT-PWR150

0 watts

AT-PWR250

0 watts

AT-PWR250-80

0 watts

AT-PWR800

380 watts

AT-PWR1200

740 watts

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды