Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 18 / 214

Chapter 1: Overview

Models

Table 1 lists the models and basic features of the x930 Series of stackable

Gigabit Layer 3 switches.

Additional information is listed here:



The switches do not come with power supplies. Power supplies

must be ordered separately. For more information, refer to “Power

Supplies” on page 27.



The power budgets of the AT-x930-28GPX and AT-x930-52GPX

Switches for PoE+ powered devices depend on the number and

types of power supplies installed in the units. For more information,

refer to “Power Budget” on page 34.



You may use the VCStack feature to stack the switches with the

S1 and S2 ports, the optional AT-StackQS card, or the 10/100/

1000Mbps front panel ports. For more information, refer to Chapter

2, “Virtual Chassis Stacking” on page 57.



The copper ports and SFP ports on AT-x930-28GSTX Switch are

paired together. Only one port in a pair can be operational at a

time. For more information, refer to “SFP Ports” on page 38.

Table 1. Models and Basic Features

Model

10/100/

1000Mbps

Copper

Ports

100/

1000Mbps

SFP Ports

1000Mbps/

10GbE

SFP+ Ports

PoE+

VCStack

AT-x930-28GTX

Yes

AT-x930-28GPX

Yes

AT-x930-28GSTX

Yes

AT-x930-52GTX

Yes

AT-x930-52GPX

Yes

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды