Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 130

Страница: 130 / 214

Chapter 8: Installing the Switch on a Wall

130

Installing the Switch on the Plywood Base

This procedure assumes that the plywood base for the switch is already

installed on the wall. Please review “Reviewing Safety Precautions” on

page 84 and “Choosing a Site for the Switch” on page 89 before

performing this procedure. Allied Telesis recommends a minimum of three

people for this procedure.

Caution

The device is heavy. Always ask for assistance before moving or

lifting it to avoid injuring yourself or damaging the equipment.

Caution

The device should be installed on a wall by a qualified building

contractor. Serious injury to yourself or others or damage to the

equipment may result if it is not properly fastened to the wall.



E105

To install the switch on the plywood base, perform the following

procedure:

1. Place the switch in a table.

2. Install the four brackets with the sixteen screws that come with the

switch to the sides of the unit, as shown in Figure 61.

Figure 61. Installing the Brackets to the Switch for Wall Installation

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды