Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 127 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

127

Installation Guidelines

Here are the guidelines to installing the switch on a wall:



You may install the switch on a wall that has wooden studs.



You may install it on a concrete wall.



If you are installing the switch on a wall with wooden studs, you

should use a plywood base to support the switch. For more

information, refer to “Plywood Base for a Wall with Wooden Studs”

on page 125. A plywood base is not required for a concrete wall.



You should not install the switch on a wall that has metal studs.

Metal studs may not be strong enough to safely support the device.



You should not install the switch only on sheetrock or similar

material. Sheetrock is not strong enough to safely support the

device.



You should install the power supplies before installing the switch

on a wall. For instructions, refer to Chapter 4, “Installing the Power

Supplies” on page 93.

Warning

The device is heavy. Always ask for assistance before moving or

lifting it to avoid injuring yourself or damaging the equipment.

Warning

The device should be installed on a wall by a qualified building

contractor. Serious injury to yourself or others or damage to the

equipment may result if it is not properly fastened to the wall.



E105

Tools and

Material

Here are the required tools and material for installing the switch on a wall:



Sixteen bracket screws (included with the switch)



Four wall or equipment rack brackets (included with the switch)



Four wall screws (included with the switch)



Four anchors for a concrete wall (included with the switch)



Cross-head screwdriver (not provided)



Stud finder for a wooden wall, capable of identifying the middle of

wall studs and hot electrical wiring (not provided)



Drill and 1/4” carbide drill bit for a concrete wall (not provided)

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды