Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 123 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

123

Recommended Minimum Wall Area Dimensions

The recommended minimum dimensions for the reserved wall area for the

switch are listed here:



Width: 68.0 centimeters (27 inches)



Height: 58.4 centimeters (23 inches)

You should position the switch in the reserved wall area such that the front

panel has more space than the rear panel. This may make it easier for you

to service and maintain the unit. Figure 57 and Figure 58 on page 124

illustrate the recommended positions of the switch in the reserved area

when the front panel is on the left and right, respectively.

Figure 57. Minimum Wall Area Dimensions with the Front Panel on the

Left

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды