Allied Telesis AT-TS24TS Скачать руководство пользователя

Страница: 61 / 64

Appendix E

Where To Find Us

For Technical Support or Service

Location

Phone

Fax

North America
United States, Canada, Mexico, Central America, South
America, Australia, New Zealand

1 (800) 428-4835

1 (206) 481-3790

France
France, Belgium, Luxembourg, The Netherlands, Middle
East, Africa

(+33) 1-69-28-16-17

(+33) 1-69-28-37-49

Germany
Germany, Switzerland, Austria, Eastern Europe

(+01) 30-83-56-66

(+49) 30-435-70-650

Italy
Italy, Spain, Portugal, Greece, Turkey, Israel

(+39) 2-38093-444

(+39) 2-38093-448

United Kingdom
United Kingdom, Denmark, Norway, Sweden, Finland,
Iceland

(+0) 800-20-40-40

(+44) 1-865-390-002

Japan

(+81) 3-3443-5640

(+81) 3-3443-2443

Asia
Singapore, Taiwan, Thailand, Malaysia, Indonesia,
Korea, Philippines, China, India

(+65) 383-2050

(+65) 383-2079

Hong Kong

(+852) 2-529-4111

(+852) 2-529-7661

Technical Bulletin Board Service

1 (206) 483-7979

CompuServe

Go ALLIED

Internet (ftp)

ftp://gateway.centre.com

World Wide Web

http://www.alliedtelesyn.com

For Information Regarding Allied Telesyn International Corp.

Allied Telesyn International Corp.

19015 North Creek Parkway Suite 200
Bothell, WA 98011
Tel:

1 (800) 424-4284

Tel:

1 (206) 487-8880

Fax:

1 (206) 489-9191

Allied Telesyn International Corp.

950 Kifer Road
Sunnyvale, CA 94086
Tel:

1 (800) 424-4282 (USA and Canada)

Fax:

1 (408) 736-0100

Содержание AT-TS24TS

































































Результаты поиска

Содержание AT-TS24TS

Отзывы:

Похожие инструкции для AT-TS24TS

Бренды по названию

Популярные бренды

Allied Telesis AT-TS24TS, Руководство по установке

Результаты поиска

Содержание AT-TS24TS

Отзывы:

Похожие инструкции для AT-TS24TS

Бренды по названию

Популярные бренды