Allied Telesis AT-TQ6602 Скачать руководство пользователя страница 26

Страница: 26 / 108

Chapter 1: Product Description

Note

You should connect the LAN port to a network device that also

supports Auto-Negotiation. The LAN port operates at 10Mbps if it is

connected to a network device does not support Auto-Negotiation.

This may result in reduced network performance.

Duplex Mode

The LAN port can operate in either half- or full-duplex mode at

10/100Mbps, and full-duplex mode at higher speeds. The port is IEEE

802.3u-compliant and uses Auto-Negotiation to set the duplex mode. You

cannot disable Auto-Negotiation on the port.

Note

You should connect the LAN port to a network device that also

supports Auto-Negotiation for duplex mode. If connected to a

network device that does not support Auto-Negotiation, it operates

at half-duplex mode. This will result in a duplex mode mismatch if

the network device is operating at full duplex. This may result in

reduced network performance.

Automatic MDIX

Detection

The LAN port is IEEE 802.3ab compliant. It features automatic MDIX

detection when operating at 10/100Mbps. (Automatic MDIX detection

does not apply to higher speeds.) This feature automatically configures

the port to MDI or MDIX depending on the wiring configuration of the port

on the network device where it is connected.

You cannot disable automatic MDIX detection. For automatic MDIX

detection to work properly, this feature must also be present on the

network device. The LAN port defaults to MDIX if it is connected to a

network device that does not support automatic MDIX detection.

Содержание AT-TQ6602













































































































Результаты поиска

Содержание AT-TQ6602

Отзывы:

Allied Telesis AT-TQ6602, Руководство по установке, Страница: 26 / 108

Результаты поиска

Содержание AT-TQ6602

Отзывы: