Allied Telesis AT-MWS1750AP Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 58

Allied Telesis AT-MWS1750AP Скачать руководство пользователя страница 18

Chapter 1: Product Description

18

LAN Port

The AT-MWS600AP and AT-MWS1750AP models are equipped with one
PoE+ LAN port; The AT-MWS2533AP model is equipped with two PoE+
LAN ports. The LAN port connects the access point to your Local Area
Network (LAN), typically through an Ethernet switch. Together with the
power supply unit, the LAN port provides a redundant power system. For
more information, see “Redundant Power Supply” on page 20.

Power over

Ethernet Plus

(PoE+)

The MWS series access point supports Power over Ethernet Plus (PoE+)
on the LAN port(s). The access point is a PoE+ class 4 powered device
and its maximum power consumption is shown below:



AT-MWS2533AP model: 21 watts



AT-MWS600AP and AT-MWS1750AP models: 11 watts

When the port is connected to a PoE+ Ethernet switch, the access point
receives its power over the network cable that carries the network traffic.

Connector Type

The LAN port has an eight-pin RJ45 connector. The port uses four pins at
10 or 100 Mbps and all eight pins at 1000 Mbps. The pin assignments are
listed in “LAN Port” on page 57.

Speed

The LAN port can operate at 10, 100, or 1000 Mbps. The speed is set
automatically with Auto-Negotiation. You cannot disable Auto-Negotiation
on the port.

Note

The LAN port should be connected to a network device that also
adjusts its speed with Auto-Negotiation. If the network device does
not support Auto-Negotiation, the LAN port operates at 10 Mbps,
which may reduce network performance.

Duplex Mode

The LAN port can operate in either half- or full-duplex mode at 10 or 100
Mbps, and full-duplex mode at 1000 Mbps. The port is IEEE
802.3u-compliant and uses Auto-Negotiation to set the duplex mode. (You
cannot disable Auto-Negotiation on the port.)

Note

The LAN port should be connected to a network device that also
sets its duplex mode with Auto-Negotiation. If the network device
does not support Auto-Negotiation, the LAN port operates at
half-duplex mode. This may result in a duplex mode mismatch if the
network device is operating at full duplex.

«
...
16
17
18
19
20
...
»

Содержание AT-MWS1750AP



























































Отзывы:

Нет отзывов