Allied Telesis AT-FAN08 Скачать руководство пользователя страница 27

Страница: 27 / 214

AT-SBx908 GEN2 Installation Guide for Virtual Chassis Stacking

Management Panel

The components on the management panel are identified in Figure 4.

Figure 4. Management Panel

Note

The management panel is not field-replaceable.

USB Port

You can use the USB port with a flash drive to perform the following
management functions:



Provide a centralized network backup location for Allied Telesis
Management Framework.



Store backup copies of configuration files.



Transfer configuration files between switches that are to have
similar configurations.



Store or transfer log files.



Store or transfer debug files (for example, the output of the SHOW
TECH-SUPPORT command).



Boot the AlliedWare Plus operating system and master
configuration file from flash drive.

Using a flash drive with the switch is optional.

USB Slot

NET MGMT

Port

CONSOLE

RS-232

Serial Port

Switch ID

LED

eco-friendly

Button

Reset Button

Содержание AT-FAN08























































































































































































































Результаты поиска

Содержание AT-FAN08

Отзывы:

Похожие инструкции для AT-FAN08

Бренды по названию

Популярные бренды

Allied Telesis AT-FAN08, Руководство по установке

Результаты поиска

Содержание AT-FAN08

Отзывы:

Похожие инструкции для AT-FAN08

Бренды по названию

Популярные бренды