Allied Telesis AT-FAN08 Скачать руководство пользователя страница 106

Страница: 106 / 214

Chapter 5: Powering On the Chassis

106

Verifying the Installation

Please perform the following procedure before powering on the chassis:

1. Verify that the chassis has at least one power supply in slot PSU A or

2. If the chassis has only one power supply, verify that the empty power

supply slot on the front panel is covered with a blank panel. For
instructions, refer to “Installing the Blank Power Supply Slot Cover” on
page 101.

3. Verify that you installed the power cord retaining clips on the AC power

connectors on the rear panel of the chassis. For instructions, refer to
“Installing the Power Cord Retaining Clips” on page 103

4. Verify that the grounding lug on the back panel of the chassis is

properly grounded. For instructions, refer to “Installing the Chassis
Grounding Wire” on page 84.

5. Verify that all empty line card slots on the front panel of the chassis are

covered with slot covers. If there are open slots, perform the procedure
“Installing Blank Line Card Slot Covers” on page 99.

You may now power on the chassis. For instructions, refer to “Powering
On AT-SBxPWRSYS2 Power Supplies” on page 107 or “Powering On AT-
SBxPWRSYS1-80 DC Power Supplies” on page 110:

Содержание AT-FAN08























































































































































































































Результаты поиска

Содержание AT-FAN08

Отзывы:

Похожие инструкции для AT-FAN08

Бренды по названию

Популярные бренды

Allied Telesis AT-FAN08, Руководство по установке

Результаты поиска

Содержание AT-FAN08

Отзывы:

Похожие инструкции для AT-FAN08

Бренды по названию

Популярные бренды