Allied Telesis AT-FAN08 Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 214

background image

AT-SBx908 GEN2 Installation Guide for Virtual Chassis Stacking

101

Installing the Blank Power Supply Slot Cover

If you installed only one power supply in the chassis, check that the empty
power supply slot is covered with the blank power supply slot cover
included with the chassis. Do one of the following:



If the chassis has two power supplies or if the empty power supply
is already covered, go to “Installing the Power Cord Retaining
Clips” on page 103.



If a power supply slot is uncovered, continue with the procedure in
this section.

To install the bank power supply slot cover, perform the following
procedure:

1. Lift the locking handle on the bank power supply slot cover. Refer to

Figure 56. Lifting the Locking Handle on the Blank Power Supply Slot

Cover

2. Align the cover in the empty power supply slot and carefully slide it into

the slot. Figure 57 on page 102 shows the cover being installed in the
PSU B slot.

«
...
99
100
101
102
103
...
»

Содержание AT-FAN08























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AT-FAN08

Бренд: Omega Engineering Страницы: 3

BNI IOL-314-S52-P012

Бренд: Balluff Страницы: 22

COOPER POWER SERIES

Бренд: Eaton Страницы: 24

COOPER POWER SERIES

Бренд: Eaton Страницы: 16

Crouse-hinds series

Бренд: Eaton Страницы: 16

Cutler-Hammer AMPGARD

Бренд: Eaton Страницы: 4

Бренд: Black Box Страницы: 2

SRS Lighting DTS16F-DIN

Бренд: plasa Страницы: 4

MatrixPRO 8x8 DVI

Бренд: Barco Страницы: 2

Бренд: Dahua Страницы: 15

Бренд: DANLERS Страницы: 2

Бренд: CableTronix Страницы: 4

IES2100SL Series

Бренд: 3onedata Страницы: 3

S5130-EI Series

Бренд: H3C Страницы: 32

Бренд: YOKOGAWA Страницы: 74

Бренд: IOGear Страницы: 40

Бренд: Zektor Страницы: 30

Бренд: Abtus Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды