Allied Air 80G1UH2V Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 41

background image

506471-01

Page 35 of 41

Issue 1034

It is recommended that this furnace be inspected by a
qualified service technician at the beginning of each heating
season.

Filters

Filters should be checked at least every 6 weeks. Disposable
filters should be replaced when dirty, and cleanable filters
should be cleaned regularly. It is important to keep the air filters
clean, as dirty filters can restrict airflow and the blower and
induced draft motors depend upon sufficient air flowing across
and through them to keep from overheating.

Burners

Light the burners and allow to operate for a few minutes to
establish normal burning conditions. Observe the burner
flames. Compare this observation to Figure 39 to determine if
proper flame adjustment is present. Flame should be
predominantly blue in color and strong in appearance. Check
that all burners are lit, and that the flame does not impinge on
the sides of the heat exchanger.

Distorted flame or yellow tipping of the natural gas burner
flame, or long yellow tips on propane, may be caused by lint
accumulation or dirt inside the burner or burner ports, at the
air inlet between the burner and manifold pipe, or
obstructions over the burner orifice.

Use a soft brush or vacuum to clean the affected areas.

MAINTENANCE

Failure to follow the safety warnings exactly could result
in dangerous operation, serious injury, death, or property
damage.

Improper servicing could result in dangerous operation,
serious injury, death, or property damage.

• Before servicing, disconnect all electrical power to

furnace.

• When servicing controls, label all wires prior to

disconnecting. Reconnect wires correctly.

• Verify proper operation after servicing.

WARNING

ELECTRICAL SHOCK, FIRE,

OR EXPLOSION HAZARD

Lubrication

The blower motor and induced draft motor are pre-lubricated
by the manufacturer and do not require further lubricating
attention. However, the motors should be cleaned
periodically to prevent the possibility of overheating due to
an accumulation of dust and dirt on the windings or on the
motor exterior.

Typical Flame Appearance

Figure 39

Heat

Exchanger

Burner

Flame

(Blue Only)

Burner

Gas

Manifold

«
...
33
34
35
36
37
...
»

Содержание 80G1UH2V










































Отзывы:

Нет отзывов

Похожие инструкции для 80G1UH2V

Бренд: Bryant Страницы: 14

Бренд: Zhermack Страницы: 46

Бренд: Zhermack Страницы: 2

Бренд: Goodman Страницы: 19

Бренд: Lennox Страницы: 7

Бренд: USSC Страницы: 24

Бренд: Carrier Страницы: 20

Бренд: Cuppone Страницы: 100

Бренд: Fire Chief Страницы: 28

Бренд: Coleman Страницы: 8

Бренд: Coleman Страницы: 12

Бренд: KDF Страницы: 28

Бренд: ICP Страницы: 7

Бренд: ICP Страницы: 27

Бренд: EDG Страницы: 30

Бренд: York International Страницы: 16

Бренд: VERDER Страницы: 74

Бренд: VERDER Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды