Allied Air 80G1UH2V Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 41

background image

506471-01

Page 11 of 41

Issue 1034

Removing the Bottom Panel

Remove the two screws that secure the bottom cap to the
furnace. Pivot the bottom cap down to release the bottom
panel. Once the bottom panel has been removed, reinstall
the bottom cap. See Figure 11.

Horizontal Applications

The furnace can be installed in horizontal applications. Order
horizontal suspension kit (51W10) from Allied Air, or use
equivalent suspension method.

Allow for clearances to combustible materials as indicated
on the unit nameplate. Minimum clearances for closet or
alcove installations are shown in Figure 12.

This furnace may be installed in either an attic or a crawl
space. Either suspend the furnace from roof rafters or floor
joists, as shown in Figure 13, or install the furnace on a
platform, as shown in Figure 14.

NOTE:

Heavy gauge perforated sheet metal straps may

be used to suspend the unit from roof rafters or ceiling joists.
When straps are used to suspend the unit in this way, support
must be provided for both the ends. The straps must not
interfere with the plenum or exhaust piping installation.

Cooling coils and supply and return air plenums must
be supported separately.

NOTE:

When the furnace is installed on

a

platform in

a

crawlspace, it must be elevated enough to avoid water
damage and to allow the evaporator coil to drain.

Return Air

-

Horizontal Applications

Return air must be brought in through the end of a furnace
installed in a horizontal application. The furnace is equipped
with a removable bottom panel to facilitate installation. See
Figure 11.

Figure 11

Removing the Bottom Panel

Horizontal Application

Installatioin clearances

* Front clearance in alcove installation must be 24 in. (610 mm).
Maintain a minimum of 21 in. (610 mm) for front service access.
‡ For installations on a combustible floor, do not install the furnace
directly on carpeting, tile or other combustible materials other than
wood flooring.

Figure 12

Typical Horizontal Application

Unit Suspended in Attic or Crawlspace

Figure 13

«
...
9
10
11
12
13
...
»

Содержание 80G1UH2V










































Отзывы:

Нет отзывов

Похожие инструкции для 80G1UH2V

Бренд: Goodman Страницы: 36

Бренд: Lennox Страницы: 6

Бренд: York Страницы: 4

Бренд: Trane Страницы: 44

Бренд: York Страницы: 8

Бренд: York Страницы: 16

Бренд: Empire Страницы: 14

Бренд: Winchester Страницы: 16

CARBOLITE GERO HST 12/200

Бренд: VERDER Страницы: 38

CARBOLITE GERO HTF 18/15

Бренд: VERDER Страницы: 62

CARBOLITE GERO HTF 18/8

Бренд: VERDER Страницы: 70

CARBOLITE GERO HTF 18/4

Бренд: VERDER Страницы: 68

CARBOLITE GERO HTF 18/27

Бренд: VERDER Страницы: 72

Бренд: VERDER Страницы: 80

Бренд: Shelter Furnace Страницы: 25

Бренд: Northern Stoker Страницы: 28

Бренд: COMFORT-AIRE Страницы: 32

Бренд: COMFORT-AIRE Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды