Alliance Laundry Systems AT120CSH Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 72

background image

48

M412982

Section 6 Adjustments

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

64. MAIN GAS BURNER AIR INLET

SHUTTERS
(All Gas Models)
Refer to Figure 22.

Air inlet shutter adjustments will vary from
location to location and will depend on the vent
system, number of units installed, make-up air and
line gas pressure. Opening the shutter increases
the amount of primary air supplied to the burner
while closing the shutter decreases the air supply.
Adjust the air shutter as follows:

a. Remove access panel.
b. Start tumbler and check the flame pattern.

Correct air and gas mixture is indicated if the
flame pattern is primarily blue, with small
yellow tips, and bends to the left of the heater
section. Too little air is indicated if the flame is
yellow, lazy and smokey.

c. To adjust the air inlet shutter, loosen locking

screw.

d. Slide shutter in or out as necessary to obtain

desired flame intensity.

e. After shutter is adjusted, tighten locking screw

securely.

f. If the flame pattern is straight up, insufficient

air is flowing through the tumbler. A flame
pattern that flares to the right and left indicates
that no air is flowing through the tumbler.

The air inlet shutters on the burner must be
adjusted so sufficient primary air is
metered into the system for proper
combustion and maximum efficiency.
Before adjusting the inlet shutter be sure
that all lint is removed from lint
compartment and lint screen.

W281

CAUTION

Figure 22

T197SE3C

AIR SHUTTER

ADJUSTING SCREW

INSUFFICIENT AIRFLOW

PROPER AIRFLOW

T196SE3C

AIR SHUTTER

ADJUSTING SCREW

T195SE3C

AIR SHUTTER

ADJUSTING SCREW

NO AIRFLOW

«
...
44
45
46
47
48
...
»

Содержание AT120CSH









































































Отзывы:

Нет отзывов

Похожие инструкции для AT120CSH

Бренд: DAN DRYER Страницы: 12

Бренд: wad Страницы: 27

Бренд: Parker Страницы: 106

Бренд: Smeg Страницы: 32

MANROSE FAN5653

Бренд: SImx Страницы: 2

Бренд: Gaggenau Страницы: 52

Бренд: Van Air Systems Страницы: 12

Бренд: Zenith Страницы: 20

Бренд: Frymaster Страницы: 2

Бренд: Campomatic Страницы: 30

Бренд: Jerdon Страницы: 20

Бренд: Rankam Страницы: 16

Бренд: Carmen Страницы: 32

NA-S086M4 Series

Бренд: Panasonic Страницы: 33

Бренд: Adler Europe Страницы: 64

Бренд: Adler Europe Страницы: 64

Бренд: Adler Europe Страницы: 64

Бренд: Indesit Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды