Alliance Laundry Systems 802749r1 Скачать руководство пользователя страница 6

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

802749

6

Laundry Tub Installation:

For this type of installation, the drain hose MUST be 
secured to the stationary tub to prevent hose from 
dislodging during use. Refer to 

Figure 7

. Use the 

beaded strap (supplied in accessories bag) to secure 
hose.

Step 4: Position and Level the Washer

Position washer so it has sufficient clearance for 
installation and servicing.

NOTE: Use of the dispenser drawer or washer door 
as a handle in the transportation of the washer may 
cause damage to the dispenser or door.

Place washer in position on a solid, sturdy and level 
floor. Installing the washer on any type of carpeting, 
soft tile, a platform or other weakly supported 
structures is not recommended.

For easier access to leveling legs, prop up washer with 
a wooden block. Refer to 

Figure 8

.

Place a level on the cabinet top and check if the washer 
is level from side to side and front to back.

NOTE: Level must rest on raised portion of top 
panel. Refer to 

Figure 8

.

If washer is not level, tilt washer to access the front 
and rear leveling legs. Loosen the locknuts and adjust 
legs by screwing into or out of washer base.

Make sure that the washer does not rock. When washer 
is level and does not rock, tighten locknuts securely 
against bottom of washer base. If these locknuts are 
not tight, washer will move out of position during 
operation.

Do not slide washer across floor once the leveling legs 
have been extended. Legs and base could become 
damaged.

Place rubber feet (supplied in accessories bag) on all 
four leveling legs. Refer to 

Figure 8

Verify that washer does not rock.

FLW1961N

Drain Hose

2

Beaded Strap (tape if necessary)

Figure 7 

FLW

1

2

Washers elevated above floor level must 
be anchored to that elevated surface, 
base or platform. The material used to 
elevate the washer should also be 
anchored to the floor to ensure that the 
washer will not walk or that the washer 
can not be physically pulled, tipped or 
slid from its installed position. Failure to 
do so may result in conditions which can 
produce serious injury, death and/or 
property damage.

W306

WARNING

FLW2154N

Level

2

Wood Block

3

Rubber Foot

4

Leveling Leg

5

Locknut

6

Washer Base

Figure 8 

FLW2154N

1

5

3

4

6

2

Содержание 802749r1













Отзывы: