Allen-Bradley PowerFlex 527 Скачать руководство пользователя | Manualshive

Страница: 43 / 176

background image

Rockwell Automation Publication 520-UM002B-EN-E - December 2017

43

Chapter

2

Start Up

This chapter describes how to start up the PowerFlex® 527 drive.

Prepare for Drive Start-Up

Before starting up the drive, it is recommended to perform the startup tasks
described below to ensure a smooth startup and drive operation. Ensure that the
drive is not powered (check that DC Bus voltage is less than 50V DC) before
proceeding with the startup task list.

Drive Startup Task List

1.

Disconnect and lock out power to the machine.

2.

Verify that AC line power at the disconnect device is within the rated value
of the drive.

3.

If replacing a drive, verify the current drive’s catalog number. Verify all
options installed on the drive.

4.

Verify that any digital control power is 24 volts.

5.

Inspect grounding, wiring, connections, and environmental compatibility.

6.

Verify that the Sink (SNK)/Source (SRC) jumper is set to match your
control wiring scheme. See the

PowerFlex 527 Control I/O Wiring Block

Diagram on page 34

for location.

For information on...

See page...

Prepare for Drive Start-Up

Understanding the PowerFlex 527 Display and Indicators

Drive Programming Tools

Language Support

Using the Ethernet Port

IMPORTANT

Read the section

General Precautions on page 11

before proceeding.

ATTENTION:

Power must be applied to the drive to perform the following

start-up procedures. Some of the voltages present are at incoming line
potential. To avoid electric shock hazard or damage to equipment, only
qualified service personnel should perform the following procedure.
Thoroughly read and understand the procedure before beginning. If an event
does not occur while performing this procedure,

Do Not Proceed. Remove All

Power

including user supplied control voltages. User supplied voltages may

exist even when main AC power is not applied to the drive. Correct the
malfunction before continuing.

«
...
41
42
43
44
45
...
»

Содержание PowerFlex 527

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerFlex 527

Бренд: Farfisa Страницы: 20

Бренд: Racal Instruments Страницы: 64

Бренд: Lamtec Страницы: 22

Бренд: Magellan Страницы: 2

Бренд: Saftronics Страницы: 13

Бренд: Watlow Страницы: 59

Tekmar WiFi Snow Melting Control 670

Бренд: Watts Страницы: 48

GA Industries 930-DT

Бренд: Vag Страницы: 4

Бренд: National Instruments Страницы: 17

Бренд: Davey Страницы: 12

Бренд: Jäger Страницы: 18

Бренд: Daruifuno Страницы: 24

Бренд: Watts Страницы: 17

SAE 07.2 Series

Бренд: AUMA Страницы: 116

Бренд: Gemini Страницы: 9

Бренд: M-system Страницы: 18

Бренд: Sherlotronics Страницы: 2

Бренд: Pacostar Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды