Allen-Bradley 1771-OD Скачать руководство пользователя страница 7

Страница: 7 / 8

AC (120V) Isolated Output Module

(Cat. No. 1771-OD)

Installation Data

Figure 3

Status Indicators

Red Output

Indicators

Status

Clear Fuse Blown

Indicators

ISOLATED

AC OUTPUT

10595-I

Replacing a Fuse

Each module output is individually fused. You can easily access the
module fuses by removing the front component–side cover.

ATTENTION: Remove power from the 1771 I/O chassis
backplane and wiring arm before removing or installing an I/O
module.

Failure to remove power from the backplane could cause
injury or equipment damage due to possible unexpected
operation.

Failure to remove power from the backplane or wiring arm
could cause module damage, degradation of performance, or
injury.

If a blown fuse occurs:

Turn off power to the I/O chassis backplane.

Pivot the wiring arm away from the module and pull the module from
the I/O chassis.

Remove the front component side cover from the module by
removing the screws securing the cover to the module.

Replace the blown fuse.

Replace the protective cover and install the module in the I/O chassis.

Reposition the wiring arm.

Restart system power.

Содержание 1771-OD









Результаты поиска

Содержание 1771-OD

Отзывы:

Похожие инструкции для 1771-OD

Бренды по названию

Популярные бренды

Allen-Bradley 1771-OD, Данные установки

Результаты поиска

Содержание 1771-OD

Отзывы:

Похожие инструкции для 1771-OD

Бренды по названию

Популярные бренды