2
WZ
3
12MON
SYS-LINK Option Fitting Instructions AP7007
Step 1:
Preparation
Ensure the console is powered off.
Disconnect the mains power lead and all
connected cables.
Ensure the work surface is approximately twice
the depth of the unit.
Remove the console from its rack or other
furniture and place on the work surface.
Step 2:
Remove the base
Start by removing the side trims if fitted: One
M4x10 and three M4x8 Pozi screws per side.
Turn the console upside down.
Release the two M4x8 flange Pozi head pod
securing screws and rotate the connector pod to
gain access to the three M3x6 Torx rear base
fixing screws.
Remove these screws and rotate the pod again
to remove the four M3x6 Pozi underside base
screws.
Carefully lift off the base.
Step 3:
Open the connector panel
Remove the two M3x6 Posi screws from each
side of the connector panel. Remove the six
M3x6 Pozi screws from the rear of the connector
panel. Carefully tilt the connector panel away
from the console so that it is flat on the work
surface.
REMOVE 2x M3 POZI SCREWS PER SIDE
Step 4:
For OUT Option Only
A connection needs to be made between two
console circuit cards before the SYS-LINK
option is fitted. Solder the supplied Violet wire
between P10 on Mix Master PCB and the SYS-
LINK plated through hole on the distribution PCB
as shown below.
WARNING: THIS APPARATUS MUST BE EARTHED
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR.
RISK OF ELECTRIC SHOCK
CAU TION
DO NOT OPEN
100 - 240V~ 47-63Hz 45W MAX
AC MAINS IN ~
FUSE
T630mA L 250V 20mm
ON
I
0
OFF
EXTERNAL DC IN
ONLY USE RECOMMENDED ALLEN&HEATH POWER SUPPLY.
REFER TO USER GUIDE FOR DETAILS.
BACKUP SUPPLY
IN
INSERT
OUT
1
INSERT
SPLIT
1
INSERT
OUT
2
GROUND LIFT
IN
SPLIT
INSERT
2
INSERT
OUT
3
INSERT
OUT
4
INSERT
OUT
5
INSERT
OUT
6
INSERT
OUT
7
INSERT
OUT
8
INSERT
OUT
9
INSERT
OUT
10
INSERT
OUT
11
INSERT
OUT
12
IN
SPLIT
INSERT
3
IN
SPLIT
INSERT
4
IN
SPLIT
INSERT
5
IN
SPLIT
INSERT
6
IN
SPLIT
INSERT
7
IN
SPLIT
INSERT
8
IN
SPLIT
INSERT
9
IN
SPLIT
INSERT
10
IN
SPLIT
INSERT
11
IN
SPLIT
INSERT
12
IN
SPLIT
INSERT
13
IN
SPLIT
INSERT
14
IN
SPLIT
INSERT
15
IN
SPLIT
INSERT
16
USER OPTION PORT A
L
R
L
R
MONITOR
EXT MONITOR IN
USER OPTION PORT B
OUT
(2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
Serial No.
(1) this device may not cause harmful interference, and
ENGINEERED IN ENGLAND BY ALLEN & HEATH LIMITED
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
ATTENTION: REMPLACER PAR UN FUSIBLE STRICTEMENT IDENTIQUE EN VALEURS.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
REPLACE FUSE WITH SAME TYPE AND RATING.
REMOVE 6 x M3 SCREWS
REMOVE SIDE TRIMS
REMOVE M4 POZI SCREW PER SIDE
ROTATE POD
REMOVE 4x M4 POZI SCREWS PER SIDE
REMOVE 3x M3 TORX SCREWS
REMOVE 4x M3 POZI SCREWS
ROTATE POD
Plated thru hole
P10
