background image

GL2200

 

U

SER 

G

UIDE

 

 

C

ONNECTING 

P

OWER TO THE CONSOLE

 

Refer to the 

SAFETY WARNING

 on page 4 of this User Guide. Read and understand the warnings 

and instructions printed on the rear panel of the console and printed here. 

The 

GL2200

 console can be powered from either the internal power supply, from an external 

DC supply such as the Allen & Heath 

RPS11

, or both together. The LED indicators on the rear 

panel illuminate to indicate which supply is active. 
Normally the internal power supply will be used to power the console by the standard 3 pin IEC 
mains input connector.  A mains cable with moulded mains plug suitable for the local supply is 
supplied. Check that the correct mains lead with moulded plug has been supplied with your 
console. Ensure that the IEC mains plug is fully inserted into the rear panel socket before 
switching on. 

P

OWER 

S

UPPLY

 

The internal power supply for the 

GL2200

 is a switch mode supply and will operate from a wide 

range of mains input voltages. It produces the DC voltages required by the console. Before 
switching on your console, check that the ac mains fuse is of the correct type and rating.  This is 
clearly marked on the rear panel of the console.  Do not replace the fuse with any other type, as 
this could become a safety hazard and will void the warranty. 

 

AC~ mains input voltage 

Fuse value 

100 - 230V ±10% 

T 1A 250V 20mm 

 

DO NOT OB

SEE INSTA

WARNING: TO REDUC

T1A 250V 20mm

WARNING - THIS APPARATUS MUST BE EARTHED.

EXTERNAL SUPPLY

INTERNAL SUPPLY

ACTIVE

ACTIVE

100 - 240V~

100 - 240V.AC

47-63Hz ~ 60W MAX

SUPPLY VOLTAGE RANGE:

NO USER S

WARNING: DISCONNECT SUPPLY BEFORE CHANGING FUSE.

ATTENTION: COUPER L'ALIMENTATION AVANT DE CHANGER LE FUSIBLE.

CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE

ATTENTION: REMPLACER LE FUSIBLE AVEC UN DES MEMES CARACTERISTIQUES.

WITH SAME TYPE AND RATING.

Ensure adequate ventilation around the console.  Do not cover the 
console or position it on soft furnishings during operation.   

The console must be connected to 0V ground by either the a.c. 
mains input cable or by the EXTERNAL DC IN cable. 

CAUTION: For continued protection against the risk of fire, replace 
fuse only with the correct type and value.

The console power supply unit contains no user serviceable parts. 
Do not remove the cover.  Refer servicing to qualified service 
personnel only. 

Содержание GL 2200





























Отзывы: