ALKOTA 435EK Скачать руководство пользователя страница 7

3

Safety & Installation

Safety Continued, Pre Start-Up, Start-Up

     05-12-06  Z08-02830A

10. If a water leak is found, 

DO NOT OPERATE THE

MACHINE.

  Shut off the motor and repair.

11.  Do not start the machine unless the gun assembly is

firmly gripped by the machine operator. Failure to do

this could result in injury from a flying hose and gun

assembly.

12.  All guards, shields, and covers must be replace after

adjustment are made to prevent accidental contact

with hazardous parts.

13. If chemicals are used in conjunction with this

equipment, read and follow the product label

directions.

14.  Do not refuel the machine while it is running or hot.

Allow it to cool sufficiently to prevent ignition of any

spilled fuel. .

15. Drive belts must be inspected and tightened

periodically to operate at optimum levels.

16.  Inspect machine for damaged or worn components

and repair or replace to avoid potential hazards.

Do not operate the machine if any mechanical

failure is noted or suspected.

17.  Always use the correct size spray tip specified in

the GENERAL section of the 

MODEL

SPECIFICATIONS

 or 

MODEL EXPLODED VIEW

.

18.  Do not start the engine until you have observed all

safety instructions and operating found in the

operating manual.

SAVE THESE SAFETY

INSTRUCTIONS

1.

The first time the machine is operated, after repairs
have been made, or if the machine has set for a period

of time (30 days or more) follow the following

procedures.
A. Check the tension of the belt (if so     equipped)

per instructions in 

MACHINE MAINTENANCE

.

B. Flush the machine per instructions in 

MACHINE

MAINTENANCE

.

2.

CAUTION:

Always use the factory supplied wash

hose with your machine. 

Do    not

 substitute other

hoses as a potential safety problem may develop.

CAUTION:

 If machine has been exposed

to sub-freezing temperatures, it must be     thoroughly

warmed to above freezing before operating.  Failure

to warm machine can cause damage to the pump
packings and other components.

♦      

Refer to the 

MAINTENANCE SCHEDULE

 for any

maintenance to be performed before

operation

OIL LEVEL

:  Check the oil level in the water pump.

BELT

:  Make sure belt tension and condition is as

specified in MACHINE MAINTENANCE.

♦ 

 

METERING VALVE ( 

if so equipped):  Make sure the

metering valve is closed before operation. If air enters

the system through this valve, poor performance and

machine damage will occur.  Refer to the metering

valve insert for proper operation.

WATER SUPPLY

:  This machine must have a water

supply meeting or exceeding the maximum discharge

volume specified in the PERFORMANCE section, and

a minimum water inlet pressure of 40 PSI /12.1KGM.

1. Turn water supply.
2. With the gun assembly in hand (on trigger gun models

hold the trigger gun valve in open   position) and with

a good flow of water turn the switch to the “pump”

position.

 CAUTION:

 A  good flow of water must be flowing

from  the end of a gun for 30 seconds, before

proceeding.  Lack of water can cause damage to

the water pump and like components.

4

Supersedes 08-19-04  Z08-02830A

 WARNING:

 Avoid the exhaust areas as they are

dangerously hot during and a short time after

operation.

 WARNING:

 Never put hands or fingers in wash

spray. DO NOT point the gun assembly toward

your body or at anyone else. Failure to do this could

result in serious injury.

 WARNING:

 DO NOT run engine in an enclosed

area. Exhaust gases contain carbon monoxide,

an odorless and deadly poison.

PRE START-UP

OPERATION

START-UP

Содержание 435EK

































Отзывы: