Alinco DJ-196 Скачать руководство пользователя страница 15

Страница: 15 / 18

data is transferred to the other transceiver.

4. The transfer is completed, "PASS" appears on the LCD.

5. Turn the power OFF, and the Clone mode is released.

If data transfer is failed, "PASS" does not appear on the LCD. Try again from the first.

7-2 Burglary Alarm Function

If someone tries to steal your transceiver, an alarm goes off from the speaker.

【

Setting

】

Be sure to set the battery pack.

1. Plug the external DC power plug cord to the car battery, etc.

2. Set to SCR-ON in the set mode.

3. Turn off the power switch of the unit.

. To release the setting, set to SCR-OF in the set mode.

【

Operation

】

. If someone unplug the power code to bring out your transceiver, an alarm goes off.

. Once the alarm goes off, it does not stop until you remove the battery pack.

. Set the battery pack and turn the power ON to release this function in the set mode.

Please set to SCR-OF in the normal operation.

7-3 External Terminal Control

"5V" is output from MIC jack terminal when the speaker is ON.

. Set to EXP-ON in the set mode.

. When receiving (The tone and code should match when the TSQ/DCS is set),

DC5V(5mA max.) is output from the center terminal of MIC stereo jack.

. Set to EXP-OF in the set mode to cancel this function.

The optional VOX MIC, etc. (EME-12, EME-13, EME-15) can not be used at EXP- ON.

7-4 MPS (Mosquito Repel Sound) Function

This function generates the supersonic that repels mosquitos from the speaker.

. Set to MPS-ON in the set mode.

. The ordinal operation is available when MPS is set.

. As the unit always generates supersonic when MPS is set, battery operating time

may become shorter.

. Set to MPS-OF to cancel the function in the set mode.

８

Set Mode

The transceiver can program the various function using the set mode.

8-1 Setting of the Set Mode

1. Press the FUNC key for more than 2 seconds, the unit enter the set mode.

2. Press the MONI key to select the menu. The monitor does not work here.

3. Rotate the dial to change the setting contents.

4. Press any key (except for the MONI key) to complete the setting. The LCD

returns to the ordinal mode.

8-2 Functions Set in the Set Mode

The following functions can be programmed in the set mode.

Содержание DJ-196



















Результаты поиска

Содержание DJ-196

Отзывы:

Похожие инструкции для DJ-196

Бренды по названию

Популярные бренды

Alinco DJ-196, Инструкция по эксплуатации

Результаты поиска

Содержание DJ-196

Отзывы:

Похожие инструкции для DJ-196

Бренды по названию

Популярные бренды