ALIGNER CCD2.0WIFI Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 16

ALIGNER CCD2.0WIFI Скачать руководство пользователя страница 7

R0368

Cod. R0368 ‐ rev.1.0

(03/2020)

Page 5/14

The

Figure 8

page appears. Pressing the F5 key

will start the WIFI search.

Figure 8

At the end of the search the references of the detectors found are reported; press F4

to confirm.

Figure 9

Attention:

if the WiFi search of the detectors does not generate results, try to enable/disable the broadcasting setting;

pressing the Alt+F2 keys shows the appearance as set out below:



Broadcasting enabled /



Broadcasting disabled (default selection)

Note: with the access point normally supplied, Zyxel NBG6604, the search is carried out with broadcasting disabled.

When the WIFI association is completed, the two icons in the
lower right corner turn BLUE.
Instead, if the association has not been carried out (or the front
detectors are off) these icons are GREY.

Note: the Bluetooth icons highlighted in RED indicate that the SW
driver that manages the system is not already running

Important: to test the actual connection with the detectors, use the
communication test (FW release) described in para. 6.1

At this point it is possible to carry out the calibration and test procedures (chap. 5 and chap. 6).

«
...
5
6
7
8
9
...
»

Содержание CCD2.0WIFI

















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды