5
www.observint.com
© 2019 Observint Technologies. All rights reserved.
To adjust the tilt, slightly loosen the tilt lock screws on both sides of the gimbal, grasp the camera
head and tilt as needed for the image height in the Live View display. Retighten the screws.
Tilt range:
0˚ ~ 75˚
Tilt lock screw (on each side)
3.
Ensure the dome assembly is clean and dust free, and then reinstall it.
4.
Refer to the recorder or camera firmware user manual for configuration adjustments to the camera.
Specifications
Camera
Image Sensor
1/2.8” progressive scan CMOS
Min. Illumination
Color: 0.01 Lux @ (F1.2, AGC ON), 0.028 Lux @ (F2.0, AGC ON);
Shutter Speed
1/3 s ~ 1/100, 000 s
Slow Shutter
Yes
Auto-Iris
No
Day & Night
IR cut filter
Digital Noise Reduction
3D DNR
WDR
Digital WDR
Angle Adjustment
Pan: 0° to 355°, tilt: 0° to 70°
Lens
Focal Length, FOV
2.8 mm, horizontal FOV 114°, vertical FOV 62°, diagonal FOV: 135°
Aperture
F2.0
Focus
No
Lens Mount
M12
IR
IR Range
up to 100 ft Smart IR
Wavelength
850 nm
Compression Standard
Video Compression
Main stream: H.265 / H.264
Sub-stream: H.265 / H.264 / MJPEG
H.264 Type
Baseline Profile / Main Profile / High Profile
H.264+
Main stream supports
H.265 Type
Main Profile
H.265+
Main stream supports
Video Bit Rate
32 Kbps ~ 8 Mbps
Smart Feature set
Region of Interest (ROI)
1 fixed region for main stream and sub-stream
Image
Max. Resolution
1920 × 1080
Main Stream Max. Frame Rate
50 Hz: 25 fps (1920 × 1080, 1280 × 960, 1280 × 720)
60 Hz: 30 fps (1920 × 1080, 1280 × 960, 1280 × 720)
Sub-stream Max. Frame Rate
50 Hz: 25 fps (640 × 480, 640 × 360, 320 × 240)
60 Hz: 30 fps (640 × 480, 640 × 360, 320 × 240)
Image Enhancement
BLC, 3D DNR
Image Settings
Saturation, brightness, contrast, sharpness, AGC, white balance adjustable by client software
or web browser
Day/Night Switch
Auto, Scheduled
Network
Alarm Trigger
Motion detection, video tampering alarm, illegal login
Protocols
TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, NTP, UPnP™, SMTP, IGMP,
802.1X, QoS, IPv6, UDP, Bonjour
General Function
Anti-flicker, heartbeat, mirror, password protection, privacy mask, watermark
API
ONVIF (PROFILE S, PROFILE G), ISAPI
Simultaneous Live View
Up to 6 channels
User/Host
Up to 32 users 3 levels: Administrator, Operator and User
Client
Alibi Central Management Software (ACMS) v3.1 or later, ACMS-XP
Web Browser
Microsoft
©
Internet Explorer
©
7 and later
Interface
Communication Interface
1 RJ45 10M/100M self-adaptive Ethernet port
General
Operating Conditions
-22 °F to 122 °F (-30 °C to 50 °C), humidity: 95% or less (non-condensing)
Power Supply
12 Vdc ± 25%, 5.5 mm coaxial power plug
PoE (802.3af, class 3)
Power Consumption and
Current
12 Vdc: 0.4 A, max. 5 W;
PoE: (802.3af, 37 V ~ 57 V), 0.2 A ~ 0.13 A, max. 6.5 W
Protection Level
IP67 weatherproof, IK10 impact resistance
TVS 2000V lightning protection, surge protection and voltage transient protection
Material
Plastic and metal
Dimensions
Φ 4.4” × 3.2” (Φ 111 mm × Φ 82.4 mm)
Weight
Camera: approx. 0.9 lb. (410 g)
With package: Approx. 1.3 lb. (610 g)
Using the Waterproof Ethernet Fitting
Install the
Waterproof Ethernet Fitting
on the Ethernet cable end at the camera when moisture or
contamination exists in the area near the camera. The fitting includes several parts that must be installed in
a specific order. To install the fitting:
1.
Place the rubber O-ring over the camera drop cable end cap.
Push the O-ring up to the connector cap.
2.
If an RJ-45 connector is installed on the network cable, from
the router or switch, remove it.
3.
Place the Lock Nut onto the network cable from the router
or switch as shown in the drawing to the right. The inside
threads must be toward the camera end.
4.
Place the rubber basket onto the network cable above the lock
nut as shown.
5.
Place the end cap onto the network cable above the rubber
gasket as shown. The fingered end must be toward the router
or switch.
6.
Install an RJ-45 connector onto the network cable.
7.
Plug the RJ-45 connector with the network cable into the
camera network drop cable.
8.
Fit the end cap on the network cable onto the camera drop
cable end cap. Rotate the network cable end cap to lock it in
place.
9.
Push the rubber gasket fully into the end of the network cable
end cap.
10. Screw the lock nut onto the network cable end cap until it is
fully seated.
Network drop
cable from
camera
Network cable from
router or switch
Fitting assembled
Waterproof Ethernet Fitting assembled and connected
Drop cable
end cap
Network drop
cable from
camera
Rubber
O-ring
seal
RJ-45
connector
End cap
Rubber
gasket
Network
cable
from
router or
switch
Lock nut
