Algo 8180 Скачать руководство пользователя страница 51

Страница: 51 / 51

- 51 -

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy, and if it is not installed and used in accordance with the instruction

manual, it may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference, in which case

the user will be required to correct the interference at his own expense.

Important Safety Notice

The 8180 is intended for installation in a dry indoor location with all connected

wiring located within the perimeter of a building.
The 8180 is a Power over Ethernet (PoE) device. The PoE power source must

be a Limited Power Source (LPS), provided by CAT5 UTP cable, and isolated

from mains by minimum reinforced or double insulation. Ensure that the PoE

injector or PoE enabled switch carries safety regulatory approval marks (ie CSA,

UL, CE).

Optional 8180 Accessories

1186 Horn Speaker

1127 Visual Alerter

1128 Strobe Light

algosolutions.com/1186

algosolutions.com/1127

algosolutions.com/1128

Algo Communication Products Ltd.

4500 Beedie Street

Burnaby, BC Canada V5J 5L2

www.algosolutions.com

Содержание 8180




















































Результаты поиска

Содержание 8180

Отзывы:

Бренды по названию

Популярные бренды

Algo 8180, Руководство пользователя

Результаты поиска

Содержание 8180

Отзывы:

Бренды по названию

Популярные бренды