Alfa Laval Tri-Clover 741 Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 34

Alfa Laval Tri-Clover 741 Series Скачать руководство пользователя страница 15

- 15 -

MAINTENANCE

TYPE 80 ACTUATOR

INTRODUCTION

Type 80 is a three position actuator that will require minimum maintenance. It is similar to the
Type 10 & 20 spring return actuators except for a mid position adjustment assembly.
Installation, adjustment, maintenance, partial disassembly, and assembly instructions are
covered below.

INSTALLATION

Connect air supply to the two

1

/

8

-27 FNPT ports. Each port is identified permanently to indicate

operation. MID — air supply causes actuator to extend to mid position. FULL — air supply
causes actuator to extend fully. Air Supply Specification: 60 - 80 psig.

Part Number

Qty

Description

1

17-98

1

Packing

2

17-345-U

1

O-Ring

3

25-454-06

1

Bushing

4

17-35-U

1

O-Ring

5

25-454-09-316L

1

Spacer

6

25-428-05

1

Seal Retainer

7

25-454-01-S

1

Cylinder Ass'y

8

25-454-07-S

1

Retainer

9

17-149-U

2

O-Ring

10

25-454-05-316

1

End Cap

11

25-454-10-316

1

Cover Plate

12

LWA1300-SS

4

Lockwasher

13

SC1315H-SS

4

Hex Bolt

14

13-170-S

1

Adjusting Nut

15

16-163

1

E-Ring

16

25-454-08

1

Adj. Nut Cover

Type 80 Actuator Replacement Parts

Full

Mid

ADJUSTMENT

There is one adjustment and it sets the mid position stop. This stop determines the length of
mid position stroke.

1

Loosen four end cap bolts until plastic adjustment knob can be turned by hand.

2

Turn plastic knob as described below for required action. COUNTERCLOCKWISE — Increase
Stroke, CLOCKWISE — Decrease Stroke

3.

Tighten four end cap bolts.

BUSHING/PACKING REMOVAL

The valve end contains one bushing and packing identical to Type 10, 20, and 30 actuators.
They are located on the valve end of the actuator.

1

Disassemble the actuator from the valve completely.

2

Assemble the yoke to the actuator without the green bushing retainer. Assemble the valve
stem to the actuator stem.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
13
14
15
16
17
...
»

Содержание Tri-Clover 741 Series



































Отзывы:

Нет отзывов