background image

Exploded and Parts List for 

HR90015, HR90030, HR90045, HR90065 HR90075

Operation 

1. Check reel for correct operation by slowly pulling out the hose. A “clicking” noise will be 

heard every half revolution of the drum. 

2. To latch the reel, pull out the hose and allow it to retract after hearing the first second or third 

“ click”. 

3. To unlatch, slowly pull out the hose until the “clicking” noise stops, then let the hose retract 

until the hose stop rests against the hose guide. Note: To avoid damage to the reel, always 
hold on to the hose while it is rewinding. 

4. Periodically check the hose condition for wear or damage, and check the swivel fitting for 

leakage. Replace any worn, damaged, or leaking parts. 

Adjustment of Spring Tension 

1. Pull out approximately 6ft or 2m of hose and allow the drum to latch. 
2. Remove hose stopper from hose, and feed hose back through guide. 
3. Wrap the pulled hose one time around the drum to increase tension or un-wrap hose one 

time from drum to decrease tension. 

4. Re-insert hose through guide, and install stopper onto hose end. 
5. Unlatch the Drum and check tension. Pull hose from reel, and adjust stopper position if 

necessary. 

Replacement of Hose 

1. Turn off supply to reel. 
2. Pull out all the old hose and lock the reel in this position. Caution: Make sure reel drum is 

securely locked and cannot rotate back. 

3. Remove two hose clamps from hose. 
4. Carefully disconnect hose from swivel joint on side of reel, or male fitting in axle center and 

remove old hose. 

5. Feed new hose through guide and opening in drum, and connect to swivel. Re-install two 

hose clamps, on inside and outside of drum flange. Install stopper on other end of hose in the 
same position as before. 

6. Carefully release the drum latch, and slowly allow the hose to wind onto the reel. Note: Final 

spring adjustment is accomplished by adding or removing wraps of hose around the drum. 
(Details see spring tension adjustment). 

Spring Canister Warning 

If the rewind spring fails for any reason: For safety reasons, the manufacturer strongly 
recommends the replacement of the spring canister be carried out by a professional mechanic. 

Limited Warranty 

1. The manufacturer warrantees this hose reel against defects in material and craftsmanship, for 

a period of 12 months from date of purchase. 

2. Hose, if supplied with reel, O-rings, plastic rollers and rubber stopper are deemed to be 

normal wear items; not warranted. 

3. Manufacturer’s liability is limited to replacement or repair of defective material within the 

warranty period, when returned freight prepaid to the distributor or their designated service 
depot. 

4. The warranty does not cover damage caused by accident, misuse or faulty installation. 
5. The reel must be installed and maintained in compliance with the instructions. 

Industrial Hose Reel 286X Series Instruction 

6 OF 9

Industrial Hose Reel 286X Series Instruction 

7 OF 9

Part No.

1
2
3
4
5
6
7
8
9

10
11
12
13
14
15
16
17
18
19
20
21
22
23

Description
Base Assembly
Spring 
Nut
Screw
Axle Sleeve 
Protection Cover
Spring Core
Screw
Hose Assembly
Drum Assembly 
Protection Base
Fitting
Support plate 2
Locking Ring  Gasket
Screw
End Cap
Hose Assembly
Convert Fitting
Fitting
Thread protector
Valve Assembly
O-Ring
O-Ring

Q’ty

1
1
6
8
1
1
1
6
1
1
1
1
1
1
3
2
1
1
1
1
1
1
1

Part No.

24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45

Description
Axle Sleeve 
Locking Ring
Screw
Screw
Drum 1
Support Plate 1
Bumper Block
Thread protector
Roller  
Roller Axle
Roller  Base
Roller  
Roller Axle
Screw
Ratchet  
Ratchet Srping
Washer
Bolt
Washer
Washer
Ball
Nut

Q’ty

1
1
6
6
1
1
1
2
2
2
4
4
2
4
1
1
1
1
1
1
1
1

26 16 4

37

29

7

28

3 8

9

30 10 11

12

2 5

41

42

39

40

14

25

24

18

21

19

17

34

36 33 32

1

35

13

15

38

43 44 45

6

23 22

20

31

27

8

Visit our website at 

www.alemlube.com.au

 or 

www.alemlube.co.nz

NSW

TEL: (02) 9677 1555
FAX: (02) 9675 1155

QLD / PNG

TEL: (07) 3204 9166
FAX: (07) 3204 1224

VIC / TAS

TEL: (03) 8787 8288
FAX: (03) 8787 8266

WA

TEL: (08) 9302 4199
FAX: (08) 9303 2095

SA / NT

TEL: (08) 8241 7111
FAX: (08) 8241 7011

NZ

TEL: (64) 9 447 1007
FAX: (64) 9 447 1008

Содержание HR90000 Series











Отзывы: