background image

Visit our website at  

www.alemlube.com.au

 or 

www.alemlube.co.nz

NSW/ACT
TEL: (02) 9677 1555
FAX: (02) 9675 1155

QLD/PNG
TEL: (07) 3204 9166
FAX: (07) 3204 1224

VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266

WA
TEL: (08) 9302 4199
FAX: (08) 9303 2095

SA/NT
TEL: (08) 8241 7111
FAX: (08) 8241 7011

NZ
TEL: (09) 447 1007
FAX: (09) 447 1008

6

20V Lithium-ion Cordless Grease Gun 450g

OWNER’S TECHNICAL MANUAL

630A

FILLING WITH A PUMP

            WARNING: 

The gun can be equipped with a low pressure filling valve (3). Never mount a high pressure lubrication 

fitting, serious damage can occur due to high pressure. Use only low pressure couplings.

1.

    Insert the rod completely into the tube.

2.

    Fasten the filling coupler on the gun filling valve (3).

3.

    Slowly start the filling pump and watch the rod move.

4.

    When the filling rod is fully extended, approximately 20cm (8 inch), stop the pump immediately. Never overfill!

5.

    Disconnect the charging coupler.

6.

    Use the bleed valve to release any trapped air. See “Grease gun priming”.

7.

    Set the display meter to zero.

GREASE PRIMING

            WARNING: 

Air pockets trapped in the grease can cause a lack or loss of priming in the gun. Always remove air after 

refilling the grease tube or when the gun loses priming and does not pump grease.

1.

    Make sure the rod is not locked.

2.

    Insert the rod into the tube.

3.

    Loosen the screw on the bleed valve without removing it completely.

4.

    Pull the trigger for 10-20 seconds.

5.

    If no grease comes out of the hose end, repeat from step 3.

OPERATION

DISPLAY AND WORKING LIGHT
Pressing the gun trigger automatically activates the display and the working LED light. To save energy, both are automatically 
switched off after 20 seconds.

The LED light can be turned on and off independently by pressing  button “A” (16).

The display shows the grease level in the cartridge, the amount of grease dispensed, the mode of operation, the units  
of measurement and the battery charge level.

GREASE FILLING 

SPEED SELECTION

The gun is equipped with 2 operating modes, a LOW mode in which a maximum flow 
rate of 100g/min is obtained and a HIGH mode in which flow rates of up to 160g/min 

 

are achieved (depending on the back pressure and the type of grease and temperature). 
In both modes the maximum working pressures of the gun can be reached, obtaining  
a longer battery life in the LOW mode.
To switch between the two operating modes, press button B, the display will alternately 
show “H” (HIGH mode active) or “L” (LOW mode active).

GREASE MEASUREMENT (ESTIMATION)
When you are supplying grease, the display will show the amount of grease dispensed  
in grams or ounces. To change units, press and hold button A for 5" to toggle between  
the two units.
An estimate of the grease level in the tube is shown graphically on the screen (15d).  

Pressing button “B” for 8” resets the counter to zero and restores the full graphic 

 

grease level indicator (15d).

BATTERY CHARGE LEVEL
The display shows 4 states of the battery charge level (15a) in graphic form. When none of the bars are visible, recharge  
the battery according to the recommended instructions.

STALL ALARM
A red light on the display indicates a blocked lube point or another issue. If a red light on the display occurs, please contact 
your local Alemlube branch for further information.

Содержание 630A









Отзывы: