background image

 

9911-1, 9911-R1

9950-1, 9950-B1

9950-C1, 9950-D1

SER 9911-1/9950-1

Service Guide

Alemite Corporation

PO Box 473515, Charlotte, North Carolina 28247-3515

www.alemite.com

Copyright 

© 

2002 by Alemite Corporation

This document contains confidential information that is the property of Alemite Corporation

670826

and is not to be copied, used, or disclosed to others without express written permission.

Revision (4-02)

Figure 1

High-Pressure Stripped Pump

Models 9911-1, 9950-1 Series

 Description

The major components of these stripped pump models consist 

of an air-operated motor that connects directly to a double-acting 
reciprocating pump tube. The pump tube is equipped with a 
dynamic primer. See Figure 2-B.

These high-pressure stripped pumps (50:1 ratio) are designed 

to deliver a range of greases [up to NLGI # 2] and operate directly 
from their original drums or bulk containers. Each pump model is 
designed with a pump tube length to accommodate different size 
containers. See Figure 1.

Specifications

Air Motor

Pump Tube

Package Models

The usage for each model of stripped pump is indicated 

below.

Piston Diameter x Stroke

Air Inlet

Maximum Air 

Pressure

Inches

Centimeters

psi

Bars

3 x 3-5/16

7.6 x 8.4

1/4 " NPTF (f)

150

10.3

For details on the air motor, refer to Service Guide SER 339413

Material

Outlet

Max. Material 

Pressure

Delivery/Minute

(Approximate)*

Displacement

per Cycle

psi

Bars

Pounds

Kilograms

In 

3

Cm 

3

3/8 " NPTF

7500

517

4.7

2.1

0.76

12.5

* For detailed information, refer to Figure 3

Table 1

High-Pressure Stripped Pump Specifications

Pump 

Model

Package Model

Pump 

Model

Package Model

9911-1

9911-H1, 9911-Z1

9950-1

9950-A1, -HC1, 9951-1, -S1, -T1

9911-R1

9911-A1, 9911-B1

9950-B1

9911-HA1

9950-C1

9911-HB1

Table 2

High-Pressure Stripped Pump Usage

High-Pressure Stripped Pump

Stripped

Pump Model

Container Size

X

Y

lbs

kg

Inches

Cm

Inches

Cm

9911-1

35

-

13.75

34.9

23.6

59.9

9911-R1

70

-

17.68

44.9

27.53

69.9

9950-1

120

50

27.75

70.5

37.6

95.4

9950-B1

-

12.5

15.50

39.4

25.35

64.3

9950-C1

-

20

19.00

48.3

28.85

73.2

9950-D1

400

180

37.06

94.1

46.91

119

Содержание 9911-1













Отзывы: