Digital Inverter Generator with Pure Sine Wave
AFTER SALES SUPPORT
e-mail: [email protected]
1800 909 909
MODEL: №. EP2800i • 09/2018 • 62007
(toll free)
AFTER SALES SUPPORT
(toll free)
Digital Inverter Generator with Pure Sine Wave
e-mail: [email protected]
1800 909 909
MODEL: №. EP2800i • 09/2018 • 62007
32
33
Maintenance
Cleaning
1. Completely empty the tank of fuel. Ensure the fuel tap/lever (23) is in the
OFF position.
2. Compress the two wire arms of the hose clamp on the outlet hose at the
fuel tap/lever (23) and slide the clamp back from the end of the hose by
approx. 25mm (Fig AF). Slide the fuel hose off the outlet of the fuel tap/
lever (23) in an anti clockwise direction.
3. Loosen the lock nut locking the fuel tap/lever (23) on to the tank
(Fig AG) in an anti clockwise direction. Unscrew the tap from the tank,
in an anti clockwise direction, and withdraw the tap from the tank.
Be careful not to lose the small seal on the thread of the tap.
4. Unscrew the fuel tap extension filter (Fig. AH).
NOTE: This filter can be cleaned in petrol to remove any build-up of dirt
on the outside of the filter, or the filter can be replaced. Do not operate
the generator without this filter in place. To replace the filter after
cleaning, or with a new filter, simply screw the filter into the inlet side of
the tap.
5. Ensuring the small seal is fitted to the tap thread, screw the tap back into
the tank by a FULL 3 – 4 turns. Orientate the fuel tap/ lever (23) so the
outlet of the tap is towards the rear of the tank, and the tap control is to
the right hand side of the tank. Holding the tap firm, tighten the lock nut
(Fig AE), ensuring the seal is clamped between the lock nut and the tank.
6. Refit the fuel hose to the outlet of the tap and with the wire arms
compressed, slide the hose clamp up onto the connection of the hose
and the tap.
7. Refill the tank with fuel and ensure there are no leaks between the fuel
tap / lever (23) and the tank, and with the fuel tap turned on, ensure there
are no leaks where the fuel hose is fitted to the outlet of the tap.
AG.
AF.
AH.
1. Keep your machine clean. The outside of the machine can be cleaned
using a damp soft cloth with a mild detergent if required. Never use water
to clean the generator as it may cause damage to internal parts.
2. Some maintenance products and solvents may damage the plastic parts;
these include products containing benzene, trichloroethylene, chloride
and ammonia.
3. Use a vacuum to clean air inlet and outlet louvres of the alternator.
4. Take special care to keep the ventilation inlets/outlets free from
obstruction; cleaning with a soft brush followed by a compressed air jet
will usually be sufficient to ensure acceptable internal cleanliness.
5. Wear eye protection when carrying out cleaning.
Your new Workzone® Titanium Inverter Generator will more than satisfy your
expectations.
It has been manufactured under stringent Workzone® Titanium Quality
Standards to meet superior performance criteria.
You will find your new Inverter Generator easy and safe to operate, and, with
proper care, it will give you many years of dependable service.
CAUTION. Carefully read through this entire instruction manual before
using your new Workzone® Titanium Inverter Generator.
Take special care to heed the Cautions and Warnings.
Your Workzone® Titanium Inverter Generator has many features that will
make your job faster and easier. Safety, performance, and dependability
have been given top priority in the development of this Generator, making it
easy to maintain and operate.
Use only Workzone® Titanium replacement parts for your product.
Non-conforming parts or modifications made to parts will void
your warranty.
Cleaning
Warranty
