background image

8

B4600 Battery-Powered Tool (

HK1189

)                                                        Alcoa Fastening Systems & Rings

o

PeratIng

 I

nstruCtIons

1.  Place fastener in workpiece, and position tool over 

fastener. 

2.  Press the tool trigger to begin fastener instalation; then 

release the trigger when the tool “kicks back”, which is 

an indicator of cycle completion. Remove the tool.

3.  If tool is adjusted correctly for swaged condition of the 

collar, one stroke will install fastener. 

The blind riveting tool features optimised operating speed. 

After inserting the blind rivet, the blind riveting tool can be 

operated in two different modes:

a.

  

Pressing and holding the switch:

 

Press and hold the switch to start riveting. The pulling 

process stops automatically when the rivet reaches the 

rear end position. The tool automatically assumes the 

front starting position when the switch is released. 

b. 

 

Tapping the switch:

 

Riveting is triggered by briefly tapping and immediately 

releasing the switch. As soon as the mandrel breaks 

off, the blind riveting tool stops and automatically re-

assumes the front starting position.

Eject the spent mandrel by tilting to the rear into the spent 

mandrel container or to the front through the nosepiece.

This tool is equipped with 

overload protection

. In the 

event of overload, e.g. by setting fasteners that are outside 

the working range, operation stops, indicated by the 3 LEDs 

flashing slowly (1 Hz). Press the switch to make the tool go 

back to the start position and it will be ready for operation.

The control detects a blockage on return (e.g. dirt, foreign 

object, etc. in the anvil assembly). The tool stops the return 

procedure and immediately assumes the rear end position 

automatically. The fault is indicated by the LEDs flashing 

rapidly (2 Hz). The battery pack must be removed and the 

fault eliminated. Then reinsert the battery and briefly press 

the switch. The tool assumes the front end position and is 

again ready for use.

This tool is fitted with an 

acoustic warning device

, which 

provides information about the remaining battery time. 

Beeps sound to tell the user when to change the battery. This 

ensures that the tool will not switch off during operation:

  

3 beeps and flashing LED lights for 10 seconds: 

The battery needs to be changed soon (about 20% 

battery charge remaining).

6 beeps and flashing LED lights for 10 seconds after 

every setting sequence: 

Change the battery after a few more riveting sequences 

in order to guarantee safe riveting sequences (approx. 

10% battery remaining).

9 beeps and flashing LED lights for 10 seconds: 

The next riveting sequence cannot be 

reliably carried out. The blind riveting tool is switched 

off. Change the battery.

WARNING: The tool moves forcibly 

while installing fasteners. Be sure there 

is adequate clearance for the tool and 

the operator’s hands before proceeding. 

Otherwise, severe personal injury may 

result.

CAUTIONS:

Tool must be held perpendicular to the 

workpiece. 

Tool must be centered on the fastener to 

ensure proper installation.

To prevent structural and tool damage, be 

sure there is enough clearance for the tool to 

move during installation process. 

P

reParatIon

 

for

 u

se

1. Remove Battery.

2. Select correct nose assembly for application. 

3. Screw in the nosepiece and tighten it. 

4. Put the battery back in and activate the switch.

WARNINGS:

When operating Huck equipment always wear 

approved eye protection. Severe eye injury 

may occur if eyes are not protected. The tool 

moves forcibly while installing fasteners. Be 

sure there is adequate clearance for the tool 

and the operator’s hands before proceeding. 

Otherwise, severe personal injury may result

 .

CAUTIONS:

Do not abuse the tool by dropping it, using 

it as a hammer, or otherwise causing 

unnecessary wear and tear. Reasonable care 

of tools by operators is an important factor 

in maintaining tool efficiency and reducing 

downtime.

Содержание B4600













Отзывы: