OAW-RAP155 / OAW-
RAP155P Remote Access
Point
Installation Guide
OAW-RAP155 / OAW-RAP155P Remote Access Point | Installation Guide
Part Number 0511330-01 | May 2013
Contacting Support
Contact Center Online
Main Site
http://www.alcatel-lucent.com/enterprise
Support Site
https://service.esd.alcatel-lucent.com
Service & Support Contact Center Telephone
North America
1-800-995-2696
Latin America
1-877-919-9526
Europe
+33 (0) 38 855 6929
Asia Pacific
+65 6240 8484
Worldwide
1-818-878-4507
Copyright
© 2013 Alcatel-Lucent. All rights reserved.
Specifications in this manual are subject to change without notice.
Originated in the USA.
AOS-W, Alcatel 4302, Alcatel 4304, Alcatel 4306, Alcatel 4308, Alcatel 4324, Alcatel 4504, Alcatel 4604, Alcatel
4704, Alcatel 6000, OAW-AP41, OAW-AP68, OAW-AP60/61/65, OAW-AP70, OAW-AP80, OAW-AP92/93, OAW-
AP105, OAW-AP120/121, OAW-AP124/125, OAW-AP175, OAW-IAP92/93/105, OAW-RAP2, OAW-RAP5, and
Omnivista 3600 Air Manager are trademarks of Alcatel-Lucent in the United States and certain other countries.
Any other trademarks appearing in this manual are the property of their respective companies. Includes software
from Litech Systems Design. The IF-MAP client library copyright 2011 Infoblox, Inc. All rights reserved. This
product includes software developed by Lars Fenneberg et al.
Legal Notice
The use of Alcatel-Lucent switching platforms and software, by all individuals or
corporations, to terminate Cisco or Nortel VPN client devices constitutes complete
acceptance of liability by that individual or corporation for this action and indemnifies, in
full, Alcatel- Lucent from any and all legal actions that might be taken against it with
respect to infringement of copyright on behalf of Cisco Systems or Nortel Networks.
Figure 5
IAP-RAP Conversion over the Internet
Wall Mounting Instructions
The two mount holes (the center-to-center distance is 26mm) are covered by the
plastic plate with Alcatel-Lucent logo on the back of the OAW-RAP155 and
OAW-RAP155P as shown in
Figure 6
. The mount holes can be used to attach the
device upright to an indoor wall as shown in
Figure 7
. To install OAW-RAP155
and OAW-RAP155P on a wall:
1. At the mounting location, install two screw on the wall, 26mm apart
2. Remove the plastic plate, align the mount holes over the screws and slide the
unit into place.
Figure 6
Mount Holes on the Back of OAW-RAP155/OAW-RAP155P
Figure 7
Mounting OAW-RAP155/OAW-RAP155P on a Wall
Product Specifications
Electrical
Ethernet:
5 x 10/100/1000BASE-T auto-sensing Ethernet RJ-45 Interfaces
MDI/MDX
10/100/1000BASE-T are IEEE 802.3 and EEE 802.3u compliant.
Power - OAW-RAP155:
12 VDC power interface, supports powering through an AC-to-DC power
adapter
Power - OAW-RAP155P:
54 VDC power interface, supports powering through an AC-to-DC power
adapter
PoE feature support (OAW-RAP155P only)
Supply PoE power to up to two IEEE 802.3af powered device (class 0-4)
on E1 and E2 port (the output power is 13 watts at each port)
Supply PoE power to one IEEE 802.3at powered device on either E1 or E2
port (the output power is 25.5 watts)
For additional specifications on this product, please refer to the data sheet. The
data sheet can be found at
www.alcatel-lucent.com
.
Proper Disposal of Alcatel-Lucent Equipment
For the most current information about Global Environmental Compliance and
Alcatel-Lucent products, see our website at
www.alcatel-lucent.com
.
Waste of Electrical and Electronic Equipment
Alcatel-Lucent products at end of life are subject to separate
collection and treatment in the EU Member States, Norway, and
Switzerland and therefore are marked with the symbol shown at
the left (crossed-out wheelie bin). The treatment applied at end
of life of these products in these countries shall comply with the
applicable national laws of countries implementing Directive
2002/96EC on Waste of Electrical and Electronic Equipment (WEEE).
European Union RoHS
Alcatel-Lucent products also comply with the EU
Restriction of Hazardous Substances Directive 2002/95/EC
(RoHS). EU RoHS restricts the use of specific hazardous
materials in the manufacture of electrical and electronic equipment. Specifically,
restricted materials under the RoHS Directive are Lead (including Solder used in
printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and
Bromine. Some Alcatel-Lucent products are subject to the exemptions listed in
RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies).
Products and packaging will be marked with the “RoHS” label shown at the left
indicating conformance to this Directive.
China RoHS
Alcatel-Lucent products also comply with China environmental
declaration requirements and are labeled with the “EFUP 10” label
shown at the left.
Safety and Regulatory Compliance
Alcatel-Lucent Networks provides a multi-language document that contains
country-specific restrictions and additional safety and regulatory information for
all Alcatel-Lucent access points. This document can be viewed or downloaded
from the following location:
https://service.esd.alcatel-lucent.com
Regulatory Model Names
The following regulatory model names apply to the OAW-RAP155 and
OAW-RAP155P:
OAW-RAP155: APINR155
OAW-RAP155P: APINR15P
EMC Compliance and Warning Statement
FCC Class B Part 15
This device complies with Part 15 of the Federal Communications Commission
(FCC) Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that
may cause undesired operation.
The device has been found to be compliant to the requirements set forth in CFR
47 Sections 2.1091 for an uncontrolled environment. The antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20 cm
from all persons and must not be co-located or operating in conjunction with any
other antenna or transmitter.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the manufacturer’s instructions, may cause interference
harmful to radio communications.
If this equipment does cause interference, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio or TV technician for help.
Complies with the Class B limits for radio noise emissions as set out in the
interference-causing equipment standard entitled “Digital Apparatus,” ICES-003
of Industry Canada.
Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement
sur le materiel brouilleur du Canada.
L ‘ utilisation de ce dispositif est autorisée seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre
prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est
susceptible de compromettre le fonctionnement du dispositif.
Le présent appareil est conforme aux normes CNR d’industrie Canada
applicables aux appareils radio exempts licence. L’exploitation est autorisée aux
deux conditions suivantes:
1. L’appareil ne doit produire de brouillage, et
2. L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
EU Regulatory Conformance
This product is CE marked according to the provisions of the R &
TTE Directive (99/5/EC) - CE(!). Alcatel-Lucent Networks, hereby
declares that the APINR155 / APINR15P device models are in compliance with
the essential requirements and other relevant provisions of Directive 1999/5/EC -
CE(!)
The Declaration of Conformity made under Directive 1999/5/EC is available for
viewing at the following location:
www.alcatel-lucent.com
.
Two mount holes
located under this
plastic plate
!
CAUTION
Alcatel-Lucent access points must be installed by a professional installer.
The professional installer is responsible for ensuring that grounding is
available and it meets applicable local and national electrical codes.
!
CAUTION
RF Radiation Exposure Statement:
This equipment complies with FCC
RF radiation exposure limits. This equipment should be installed and
operated with a minimum distance of 35cm between the radiator and
your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
10
᳝↦᳝ᆇ⠽䋼ໄᯢ
Hazardous Materials Declaration
᳝↦᳝ᆇ⠽䋼ܗ㋴
(Hazardous Substance)
䚼ӊৡ⿄
(Parts)
䪙
3E
∲
+J
䬝
&G
݁Ӌ䫀
&U
⒈㘨㣃
3%%
⒈Ѡ㣃䝮
3%'(
⬉䏃ᵓ
(
PCA Boards)
h
ƻ
ƻ
ƻ
ƻ
ƻ
ᴎẄ㒘ӊ
(
Mechanical Sub-Assemblies)
h
ƻ
ƻ
ƻ
ƻ
ƻ
ƻ˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ䞣ഛ
SJ/T11363-2006
ᷛޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ
Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is
below the relevant threshold of the SJ/T11363-2006 standard.
h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ䞣䍙ߎ6-7ᷛޚ㾘ᅮⱘ䰤䞣㽕∖DŽ
Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials
in the parts is above the relevant threshold of the SJ/T11363-2006 standard.
ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ䖭ѯ⠽䋼DŽ
This table shows where these substances may be found in the supply chain of electronic information
products, as of the date of sale of the enclosed product.
ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ
՟བ⬉∴ऩܗഫ䌈݊ѻકϞ
ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼ѢѻકᰃѻકݠЁ᠔㾘ᅮⱘᴵӊϟᎹ
The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are
per the symbol shown here. The Environment- Friendly Use Period is valid only when the
product is operated under the conditions defined in the product manual.
!
CAUTION
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.
