Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 97

Страница: 97 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 97

Configuring Physical Ports with CLI

This section provides information to configure cards, MDAs, and ports.

Topics in this section include:

•

Preprovisioning Guidelines on page 98

→

Predefining Entities on page 98

→

Preprovisioning a Port on page 99

→

Maximizing Bandwidth Use on page 100

•

Basic Configuration on page 101

•

Common Configuration Tasks on page 102

→

Configuring Ports on page 107

•

Common Configuration Tasks on page 102

→

Configuring Cards and MDAs on page 103

−

Configuring MDA Access and Network Pool Parameters on page 106

→

Configuring Ports on page 107

−

Configuring Port Pool Parameters on page 107

−

Configuring APS Parameters on page 110

−

Configuring Ethernet Port Parameters on page 113

−

Configuring SONET/SDH Port Parameters on page 115

−

Configuring Channelized Ports on page 118

−

Configuring ATM Interface Parameters on page 137

−

Configuring Frame Relay Parameters on page 142

−

Configuring Multilink PPP Bundles on page 146

−

Configuring Multilink ATM Inverse Multiplexing (IMA) Bundles on page 147

−

Configuring Bundle Protection Group Ports on page 152

→

Configuring LAG Parameters on page 155

•

Service Management Tasks on page 156

→

Modifying or Deleting an MDA on page 156

→

Modifying a Card Type on page 157

→

Deleting a Card on page 157

→

Deleting Port Parameters on page 157

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды