Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 142

Страница: 142 / 444

Configuring Ports

Page 142

7750 SR OS Interface Configuration Guide

Configuring Frame Relay Parameters

Frame Relay pipes are used to provide customer-to-customer Frame Relay PVCs or to
interconnect individual Frame Relay clouds.

Frame Relay parameters can only be configured in SONET/SDH and channelized TDM MDA
contexts.

The following example displays a channelized interface configuration:

A:ALA-7>config>port# info detail

----------------------------------------------

description "DS3/E3"

...

tdm

buildout long

ds3 ds3

type t3

channelized

clock-source loop-timed

framing c-bit

no feac-loop-respond

no mdl

no mdl-transmit

no loopback

report-alarm ais los

no report-alarm oof rai looped

no shutdown

exit

ds1 ds1-1

shutdown

framing esf

no loopback

report-alarm ais los

no report-alarm oof rai looped

channel-group 1

description "DS3/E3"

mode access

encap-type

frame-relay

no mtu

no mac

timeslots 1

speed 64

crc 16

frame-relay

lmi-type itu

mode dte

n393dce 4

n393dte 4

n391dte 6

n392dce 3

n392dte 3

t391dte 10

t392dce 15

exit

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды