Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 205 | Manualshive

Страница: 205 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 205

Syntax:

bpgrp

-

type

-

bpgrp-num

bpgrp:

keyword

type

:

ppp

— Provides protection of one PPP bundle by another.

ima

— Provides protection of one IMA bundle by another IMA

bundle.

bpg-num

:

1 — 1280

Example

:

port

bpgrp

-

ima

-29

ddm-events

Syntax

[

no

]

ddm-events

Context

config>port

Description

This command enables Digital Diagnostic Monitoring (DDM) events for the port.

The

no

form of the command disables DDM events.

modify-buffer-allocation-rate

Syntax

modify-buffer-allocation-rate

Context

config>port

Description

This command enables the context to configure ingress and egress percentage of rate parameters. This
command only applies to physical ports (for example, it will not work on APS or similar logical
ports). The percentage of rate commands are used to define a percentage value that affects the amount
of buffers used by ingress and egress port managed buffer space. Enter the modify-buffer-allocation-
rate context when editing the port’s percentage of rate commands.

ing-percentage-of-rate

Syntax

ing-percentage-of-rate

rate-percentage

no ing-percentage-of-rate

Context

config>port>modify-buffer-allocation-rate

Description

This command increases or decreases the active bandwidth associated with the ingress port that
affects the amount of ingress buffer space managed by the port. Changing a port’s active bandwidth
using the ing-percentage-of-rate command is an effective means of artificially lowering the buffers
managed by one ingress port and giving them to other ingress ports on the same MDA.

The ing-percentage-of-rate command accepts a percentage value that increases or decreases the active
bandwidth based on the defined percentage. A value of 50% causes the active bandwidth to be
reduced by 50%. A value of 150% causes the active bandwidth to be increased by 50%. Values from
1 to 1000 percent are supported.

«
...
203
204
205
206
207
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: IBM Страницы: 4

Бренд: JCG Страницы: 3

DHI-NVR2104-P-4KS2

Бренд: Dahua Страницы: 23

Бренд: WaiLan Страницы: 27

Бренд: CAME Страницы: 32

Бренд: 2N Telekomunikace Страницы: 67

Бренд: DPS Страницы: 57

IP Board IPT10000C

Бренд: Dialogic Страницы: 2

Бренд: Xantech Страницы: 6

HomePNA PCI Adapter

Бренд: City-Netek Страницы: 18

MP5S Plus Writer

Бренд: SONIX Страницы: 23

Бренд: Lanner Страницы: 141

Бренд: Proxim Страницы: 65

OmniSwitch 6624

Бренд: Alcatel Страницы: 546

Бренд: Wieland Страницы: 2

Wireless Kit 108MBPS

Бренд: Topcom Страницы: 100

ServCon FPS-3003

Бренд: LevelOne Страницы: 45

Бренд: Allied Telesis Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды