Alcatel-Lucent Enterprise OmniSwitch 6865 Скачать руководство пользователя страница 8

Страница: 8 / 63

OmniSwitch 6865 Hardware Users Guide

Chassis Front Panel

Note: For LED descriptions, refer to

“System and Port LEDs” on page 33

1588v2 Capability

Supported

PoE Power Budget

See

“Power over Ethernet Budget” on page 40

for more

information.

Power Consumption (idle)

30W

Front Panel Descriptions (Left to Right)

Console (RJ45)

For console or modem

USB Type A

For storage devices that can download code or save configuration
information, such as flash-based pen drives or external hard
drives. For Maintenance Only.

Ports 1 and 2

Two (2) fixed SFP+ (1G/10G)

Ports 3 and 4

Two (2) 1000Base-X SFP

Ports 5 through 8

Four (4) 10/100/1000Base-T PoE+ (supporting 75W HPoE per port)

Ports 9 through 16

Eight (8) 10/100/1000Base-T PoE+ (supporting 30W PoE per port)

OmniSwitch 6865-P16X Chassis Specifications

Содержание OmniSwitch 6865
































































Результаты поиска

Содержание OmniSwitch 6865

Отзывы:

Бренды по названию

Популярные бренды

Alcatel-Lucent Enterprise OmniSwitch 6865, Руководство пользователя по оборудованию

Результаты поиска

Содержание OmniSwitch 6865

Отзывы:

Бренды по названию

Популярные бренды