manualshive.com logo in svg

Alcatel-Lucent Enterprise OmniSwitch 6865, Руководство пользователя по оборудованию

Поделиться
Скачать
Alcatel-Lucent Enterprise OmniSwitch 6865 Скачать руководство пользователя страница 32

OmniSwitch 6865 Hardware Users Guide

28

 

Installing Power Supplies for Rear Mount Trays

1. Orient the power supply as shown below. Insert the guide pins (located on either side of the DB-15 

connector) into the guide holes in the rear of the chassis. 

For this example, table mount assembly shown.

2. Push the power supply into place until the connector is fully seated and tighten the thumb screw at 

the front of the power supply unit.

3. For redundant power supply configurations, repeat these steps using the power supply connector 

and thumb screw hole located at the other side of the chassis and power supply tray.

Note. The switch does not provide an on/off switch. Instead, the switch powers 
on when a power cord is plugged into the power supply’s front panel and 
plugged into a power source. 

Hole for Guide Pin

Содержание OmniSwitch 6865
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды