Albatron NForce 650i Ultra Скачать руководство пользователя страница 11

Страница: 11 / 70

Mainboard nForce 650i Ultra

FAN Headers: CPU FAN, C55 FAN

There are several fan headers available for cooling fans on the mainboard. Here describes

the two important ones only. The cooling fans play an important role in maintaining ambient

temperatures in your system. The CPUFAN header is attached with a CPU cooling fan. The
C55 FAN header is attached with the nForce SPP fan.

Pin

Assignment

1 Control
2 Sense
3 PWR

CPU FAN

GND

Pin

Assignment

1 Sense
2 +12V

C55 FAN

GND

Memory Installation: DIMM0/1/2/3

The nForce 650i Ultra mainboard provides four DIMM (Dual In-Line Memory Modules) sockets

which allow you to install 240-pin, unbuffered non-ECC, DDRII 800/ 667/ 533 SDRAMs. It also
supports Dual Channel Technology and allow you to install a total memory capacity of 8 GB.

Attention

It is recommended that to install memories which are
identical specifications (same timing specifications and same

DDR II speed) to achieve the best effects. It may cause the
failure of power-on or lower memory speed if installing

different type, SPD (series presence detects) memories.

Содержание NForce 650i Ultra







































































Результаты поиска

Содержание NForce 650i Ultra

Отзывы:

Похожие инструкции для NForce 650i Ultra

Бренды по названию

Популярные бренды

Albatron NForce 650i Ultra, Руководство пользователя

Результаты поиска

Содержание NForce 650i Ultra

Отзывы:

Похожие инструкции для NForce 650i Ultra

Бренды по названию

Популярные бренды