background image

 

 
 
 
 

nForce 650i Ultra 

 
 
Copyright 

All rights are reserved. No part of this publication may be reproduced, transmitted, 

transcribed, stored in a retrieval system or translated into any language or computer 
language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, 

manual or otherwise, without the prior written permission of the company. Brands and 

product names are trademarks or registered trademarks of their respective companies. 
The vendor makes no representations or warranties with respect to the contents herein and 
especially disclaim any implied warranties of merchantability or fitness for any purpose. 
Further the vendor reserves the right to revise this publication and to make changes to the 

contents herein without obligation to notify any party beforehand. Duplication of this 

publication, in part or in whole, is not allowed without first obtaining the vendor’s approval 

in writing. 

Trademark 

All the trademarks or brands in this document are registered by their respective owner. 

Disclaimer 

We make no warranty of any kind with regard to the content of this user’s manual. The 

content is subject to change without notice and we will not be responsible for any mistakes 

found in this user’s manual. All the brand and product names are trademarks of their 

respective companies. 

FCC Compliance Statement 

This equipment has been tested and found to comply with the limits of a Class B digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment 
generates, uses and can radiate radio frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful interference to radio communications. 

Operation of this equipment in a residential area is likely to cause harmful interference in 

which case the user will be required to correct the interference at his own expense. However, 

there is no guarantee that interference will not occur in a particular installation. 

CE Mark 

The device is in accordance with 89/336 ECC-ENC Directive. 

 

 

 
 
 

Ver: EG101 

Содержание NForce 650i Ultra







































































Отзывы: