Alarm.Com ADC-T40K-HD Скачать руководство пользователя страница 5

6

7

  Thermostat installation

    Level and mount the Thermostat to the wall 

with the supplied hardware.

•   If additional support is necessary, drill holes with a 

3/16’’ (#13) drill bit and tap in the drywall anchors.

•   If you need to cover up any marks or holes from the 

previous thermostat, mount the trim plate prior to 
securing the Thermostat to the wall.

  Insert the wires into their designated 

wire terminals. See the table for details.

  

IMPORTANT: If you only have one R wire, insert it 

into RH. Only connect wires to the thermostat that will 

be used by the system. Inserting wires that are not 

connected to or used by the HVAC system could cause 

the Smart Thermostat HD to operate improperly.

  

CAUTION: Do not insert more than one wire into a wire 

terminal as this will damage the wire terminal. If you 

only have one R wire, there is no need to physically 

jump RH and RC. The Thermostat will internally jump 

the two terminals.

Terminal

Description

RC

Cooling power

RH*

Heating power

W2

Heat/aux stage 2

W

Heat/aux stage 1

C*

Common wire from transformer

Z1

Configurable: W3, humidifier, 

dehumidifier, vent

Z2

Configurable: W3, humidifier, 

dehumidifier, vent

Y

Cool/pump stage 1

Y2

Cool/pump stage 2

G

Fan

O

Heat pump reversing valve 

(Energized in COOL mode)

B

Heat pump reversing valve 

(Energized in HEAT mode)

*Required wire

  After all wires are inserted into the wire terminals, 

restore power to the HVAC system.

 •   This will supply 24 VAC power to the Thermostat.

 

  Check the Status LED, which will indicate 

the Thermostat has power.

•   If the Status LED is off, it indicates the 

Thermostat does not have 24 VAC power.

•   Visually verify both RH and C are securely 

inserted into the appropriately labeled terminals.

•   Verify the HVAC system has power, this may 

be identified at the unit.

•   Verify the circuit breaker was correctly turned back on.

  Display installation

  Connect the Display to the Thermostat. 

Magnets will hold the Display in place.

  The Display will turn on after being connected.

•   If the display does not power on after 30 seconds, 

verify 24 VAC power is being supplied to the 
Thermostat from the HVAC system.

 Setup

•   Follow the on-screen setup wizard to configure 

the Smart Thermostat HD and connect it to 

a Z-Wave network. 

Содержание ADC-T40K-HD










Отзывы: