Alarko ALDENS 105 Скачать руководство пользователя страница 42

Страница: 42 / 76

3.3. Mounting On The Wall and The Hanging System

Before hanging on the wall, the wall mounting bracket should be mounted on a structure / wall or

a hanging construction / stack robust enough to carry the total weight. The HANG CONNECTION

PLATE (whose tip is directing the floor) will be hanged over the HANGING PLATE (wall mounting

bracket) which must be mounted stiffly onto the wall surface with the help of the lag (coach) screw

(trifon) plus the dowel (anchor) couple. Please refer to a wall and/or construction expert (e.g. civil

engineers, architects) about the reliability of the wall you are planning to hang your boiler(s).

It will be adventageous to use a lifting equipment for hanging the device on the HANGING PLATE.
For achieving a robust structure, please use the screw + dowel couples which are included in your

product’s package as 4 couples. It will also be beneficial to inject a post-drying chemical into the

dowel hole (after screwdriving the wall). The hole centers’ position dimensions with respect to the

boiler is as seen above.

3.4. Electrical Wiring Diagram and DHW Circuitry

Cross-sectional area

Maximum legnth

0.25 mm²

20m

0.5

mm²

40m

mm²

80m

1.5

mm²

120m

The system should be comissioned with the needed connections in order to also control the three-

way-valve and an accumulation tank as in the example below. This example will help you to get an

insight about a better understanding of using your condensing boiler also for domestic hot water

(DHW) production and storage (in an accumulation tank).
The below table can be used for determining the cross sectional areas and the maximum cable

lengths for the wiring. These informations are only for sensor cables.

In case of cascade system installation, connect the

B3/38 (QX3) DHW sensor to the same line terminal of

the current boiler as the DHW tank pump. This is an

adviced issue for field operations.

Rev:

Alarko montaj ve kullanım kılavuzu

Tarih: 03/04/2019

Son aşamaya gelindiğinde kazanı alt ve duvar tarafındaki kenarı üzerinde döndürerek dikkatle

havaya dikiniz. Bundan önce alt ve ön kenarından içeride kalacak biçimde ve ön kenar boyunca bir

destek koymayı unutmayınız.

3.3.

Kazanın Duvara Montajı ve Taşıyıcı Sistem Hakkında Dikkat

Edilmesi Gerekenler

Ürününüzün duvara montajı öncesinde duvar askısı parçasının sağlam bir biçimde

yapısal

bakımdan yeteri kadar dayanıklı bir duvara ya da gereksinimleri karşılayabilecek bir taşıyıcı sisteme

(ör: çelik bir karkas konstrüksiyonu)

monte edilmesi gereklidir.

Kazanın sırt (duvara bakan)

kısmında yer alan ve ucu yere doğru kıvrık asılma parçası, duvara

trifon vida ve

dübel

çifti

ile

sabitlenecek olan duvar askı parçasına asılacaktır.

Trifon vida ankrajının yapıldığı duvarın sağlamlığı

ve yapısal yeterlilikleri hakkında gerekirse bir uzmana danışınız.

Rev:

Alarko montaj ve kullanım kılavuzu

Tarih: 03/04/2019

Son aşamaya gelindiğinde kazanı alt ve duvar tarafındaki kenarı üzerinde döndürerek dikkatle

havaya dikiniz. Bundan önce alt ve ön kenarından içeride kalacak biçimde ve ön kenar boyunca bir

destek koymayı unutmayınız.

3.3.

Kazanın Duvara Montajı ve Taşıyıcı Sistem Hakkında Dikkat

Edilmesi Gerekenler

Ürününüzün duvara montajı öncesinde duvar askısı parçasının sağlam bir biçimde

yapısal

bakımdan yeteri kadar dayanıklı bir duvara ya da gereksinimleri karşılayabilecek bir taşıyıcı sisteme

(ör: çelik bir karkas konstrüksiyonu)

monte edilmesi gereklidir.

Kazanın sırt (duvara bakan)

kısmında yer alan ve ucu yere doğru kıvrık asılma parçası, duvara

trifon vida ve

dübel

çifti

ile

sabitlenecek olan duvar askı parçasına asılacaktır.

Trifon vida ankrajının yapıldığı duvarın sağlamlığı

ve yapısal yeterlilikleri hakkında gerekirse bir uzmana danışınız.

COACH SCREW 6,7x50 + DOWEL

Содержание ALDENS 105













































































Результаты поиска

Содержание ALDENS 105

Отзывы:

Похожие инструкции для ALDENS 105

Бренды по названию

Популярные бренды

Alarko ALDENS 105, Руководство пользователя

Результаты поиска

Содержание ALDENS 105

Отзывы:

Похожие инструкции для ALDENS 105

Бренды по названию

Популярные бренды