Akuvox A05 Series Скачать руководство пользователя страница 51

Страница: 51 / 77

A05 Admin Guide

AKUVOX SMART INTERCOM

www.akuvox.com



2nd Video Framerate

: select the video framerate for the second video

stream channel.

“25fps”

is the video frame rate by default for the second

video stream channel.



2nd Video Bitrate

: select video bitrate among the six options for the

second video stream channel. While the second video stream channel is

“

512 kpbs

” by default.

Note:



A05 series supports two video stream channels for H.264 codec

video stream.

11.4. ONVIF

Real-time video from the A05 series access control terminal camera can be

searched and obtained by the Akuvox indoor monitor or by the third-party

devices such as NVR (

Network Video Recorder

) you can configure the ONVIF

function in the access control terminal so that other device will be able to see

the video from the access control terminal. To configure the configuration on

web

Intercom > ONVIF

interface.

Parameter Set-up:



Discoverable:

tick the check box to turn on the ONVIF mode. If you select

video from the access control terminal camera can be searched by other

devices. ONVIF mode is

Discoverable

by default.

Содержание A05 Series














































































Результаты поиска

Содержание A05 Series

Отзывы:

Похожие инструкции для A05 Series

Бренды по названию

Популярные бренды

Akuvox A05 Series, Руководство администратора

Результаты поиска

Содержание A05 Series

Отзывы:

Похожие инструкции для A05 Series

Бренды по названию

Популярные бренды